Sharp AR-M550N Service Manual Download Page 62

Page: 62 / 460

AR-M550/M620/M700 DETAILS OF EACH SECTION 6 - 7

Code

Signal

name

Name

Function/Operation

Type

Model

Note

MPED

Manual feed paper empty
detector

Manual paper feed tray paper empty
detection

Transmission type

Manual paper feed unit

MPFD1

Manual feed paper pass
detector 1

Manual tray paper pass detection

Transmission type

Paper transport system
sensor

MPFPWS MPFPWS Manual feed paper width

detector

Manual feed paper width detection

Volume resistor

Analog detector

MPLD1

Manual feed paper length
detector 1

Manual paper feed tray paper length
detection (Paper feed side)

Transmission type

Manual paper feed unit

MPLD2

Manual feed paper length
detector 2

Manual paper feed tray paper length
detection (Outside)

Transmission type

Manual paper feed unit

MTOP1

Manual tray pull-out position
detector 1

Manual paper feed tray pull-out position
detection (Storing position)

Contact type

Manual paper feed unit

MTOP2

Manual tray pull-out position
detector 2

Manual paper feed tray pull-out position
detection (Pull-out position)

Contact type

Manual paper feed unit

DSW-R

Manual feed unit open/close
detector

Manual paper feed unit open/close
detection, main charger power/
developing bias power line open/close

Micro switch

MPFC

Paper feed clutch (Manual
paper feed)

Manual paper feed section paper feed
roller ON/OFF control

Electromagnetic
clutch

MFPUS

Paper pickup solenoid
(Manual paper feed)

Presses the paper pickup roller onto
paper.

Electromagnetic
solenoid

MPFGS

Manual paper feed gate
solenoid

Manual feed gate solenoid open/close
control

Electromagnetic
solenoid

No.

Name

Function

Separation roller (Manual paper feed tray)

Separates paper to prevent against double feed.

Paper feed roller (Manual paper feed tray)

Feeds paper to the paper transport section.

Paper pickup roller (Manual paper feed tray)

Sends paper to the paper feed roller.

Torque limiter

A fixed level of resistance is applied to the paper separation roller to prevent against double
feed.

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 62 / 460

Search results

Summary of Contents for AR-M550N

Reviews: