manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 302 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 302

AR-M550/M620/M700  SIMULATION  8 - 44

Operation/Procedure

1) Select ENABLE/DISABLE of the CA key cancel function of print

stop with 10-key.

2) Press [START] key.

(Default: 1)

Operation/Procedure

1) Select the number corresponding to the operation mode with 10-

key.

2) Press [START] key.

(Default: 0)

Operation/Procedure

1) Enter the tag number with 10-key.

2) Press [START] key.

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

26-68

Purpose

Setting

Function
(Purpose)

Used to set ENABLE/DISABLE of the CA key cancel 
function of print stop.

Section

Item

Specifications

Operation

0

DISABLE

Disable

1

ENABLE (PRINT STOP)

Enable

27

27-1

Purpose

Setting

Function
(Purpose)

Used to set the specifications for operations in case of 
communication trouble between the host computer and 
MODEM (machine side). (When communication 
trouble occurs between the host computer MODEM 
and the machine, the self diag display (U7-00) is 
printed and setting for inhibition of print or not is made.)

Section

Communication unit (TEL/LIU/MODEM etc.)

Item

Specifications

Operation mode

0

YES

Though a communication trouble occurs between the 
host computer and the MODEM (machine side), there is 
no effect on the machine operations.

1

NO

When a communication trouble occurs between the host 
computer and the MODEM (machine side), the self diag 
display (U7-00) is displayed and printing is inhibited.

SIMULATION 26-52

BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS 

START.

0. NO  (NO COUNT UP)

1. YES (COUNT UP)

1

SIMULATION 26-68

CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS 

START.

0. DISABLE

1. ENABLE (PRINT STOP)

0

SIMULATION 27-1

DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START.

0. YES

1. NO

1

27-5

Purpose

Setting

Function
(Purpose)

Used to enter the machine tag No. (This function 
allows to check the tag No. of the machine with the 
host computer.)

Section

Communication unit (TEL/LIU/MODEM etc.)

Item

Specifications

Operation mode

30

30-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of sensors and detectors 
in other than the paper feed section and the operations 
of the related circuits.

Section

Item

Operation

PFD2

ADU paper feed detection 2

PPD

Resist roller front paper detection 

PSD

Drum rear paper detection 

POD1

After-fusing transport detection 1

POD2

After-fusing transport detection 2

POD3

Paper full detection

DSW_R

Manual feed door open detection

DSW_L

Cabinet open detection

DSW_F

Front cabinet open detection 

DSW_DSK

Desk door open detection 

TFSD

Toner remaining quantity detection (Motor rotation 
number count)

THPS2

Transfer belt separation home sensor 2

LPPD

LCC paper transport detection

T1PPD

Tandem tray 1 paper transport sensor

SIMULATION 27-5

TAG # SETTING. INPUT VALUE, AND PRESS START.

PRESENT:  00010000

NEW:      

00009999

SIMULATION 30-1

SENSOR CHECK..
PFD2        

PPD

       PSD       POD1      POD2

POD3        DSW_R     DSW_L     DSW_F
DSW_DSK     TFSD      THPS2     LPPD      T1PPD

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments