manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 190 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 190

: Feb. 6 2004

1

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 135

2) Remove the tray.

3) Remove the left cover cabinet.

5) Disconnect the connector and remove the fusing motor.

[Drum drive section]

(Replacement parts)

a. Drum drive unit

1) Remove the developing unit and the process unit. (See “a. Devel-

oping unit”/4. Image process section “[OPC drum section]” and “a.
Process unit”)

2) Remove the OPC drum motor and the developing motor. (See “b-

1. OPC drum motor” in this section)

3) Disconnect the connector, and remove the harness from the har-

ness holder.

4) Disconnect the connector and remove the harness clamp, and

remove the drum drive unit.

∗

Remove the screw which was indicated with the arrow mark.

4) Disconnect the connector and remove the harness clamp, and

remove the paper exit tray duct R unit.

1

No.

Unit

Parts

a

Drum drive unit

1

Waste toner pipe lock detector

2

Process humidity sensor

b

Other

1

OPC drum motor

2

Developing motor

b-1

b-2

a-1

a-2

a

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments