manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 305 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 305

AR-M550/M620/M700  SIMULATION  8 - 47

Operation/Procedure

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

Operation/Procedure

1) Open the document cover and select NO ORIGINAL with 10-key

without placing any document on the document table.

2) Press [START] key.

The sensor level is set without document on the document table.

3) Place an A3 document on the document table, and select A3

ORIGINAL with 10-key.

4) Press [START] key.

The sensor level is set when detection the document.

If the above procedures are not completed normally, "ERROR" is dis-
played. If completed normally, "COMPLETE" is displayed.

Operation/Procedure

The detection output level (A/D value) of the document sensors (PD1 -
PD7) is displayed in real time.

∗

The value in [ ] on the side of each sensor name indicates the
threshold value.

The light receiving value (A/D value) and the threshold value (A/D
value) of PD1 - PD7 are in the range of 1 - 255. The default of thresh-
old value is 128.

Operation/Procedure

1) Select the number corresponding to the setting mode with 10-key.

2) Press [START] key.

3) Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key.

41

41-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of the document size 
sensor and the related circuit. (The operation of the 
document size sensor can be monitored with the LCD 
display.)

Section

Other

Item

Operation

OCSW

Document cover 
status

Open: Normal display

Close: Highlighted

PD1 - 7

Document detection 
sensor status

No document: Normal display
Document present: Highlighted

41-2

Purpose

Adjustment

Function
(Purpose)

Used to adjust the document size sensor sensing level.

Section

Other

Item

Operation

SIMULATION 40-12

TRAY3 ADJUSTMENT. SELECT 1-2, AND PRESS START.

1. MAX. POSITION

2. MIN. POSITION

1

SIMULATION 40-12

TRAY3 ADJUSTMENT.

MAX. POSITION ··· COMPLETE (or "ERROR")

Press [CUSTOM SETTINGS] key.

Select 1 and press [START] key. 

SIMULATION 40-12

TRAY3 ADJUSTMENT.

MIN. POSITION ··· COMPLETE (or "ERROR")

SIMULATION 41-1

PD SENSOR CHECK..

OCSW  

PD1

  

PD2

  

PD3

  PD4  PD5  PD6  PD7

Select 2 and press [START] key. 
(Error)

Press [CUSTOM SETTINGS] 
key.

41-3

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of the document size 
sensor and the related circuit. (The document size 
sensor output level can be monitored with the LCD 
display.)

Section

Other

Item

Operation

OCSW

Original cover status

Open: Normal display

Close: Highlighted

PD1 - 7

PD sensor detection level The value in [ ] indicates the 
adjustment threshold value (SIM41-2 adjustment value).

43

43-1

Purpose

Setting

Function
(Purpose)

Used to set the fusing temperature in each operation 
mode.

Section

Fixing (Fusing)

Item

Operation

SIMULATION 41-2

PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START.

(PLEASE OPEN THE ORIGINAL COVER.) 

1. NO ORIGINAL

2. A3 ORIGINAL

1

SIMULATION 41-2

Press [CUSTOM SETTINGS] key. 

Select 1 and 
press [START] key. 

PD SENSOR ADJUSTMENT.

NO ORIGINAL ··· COMPLETE (or "ERROR at 

PD1 PD2

...")

A3 ORIGINAL ··· INCOMPLETE

SIMULATION 41-2

PD SENSOR ADJUSTMENT.

NO ORIGINAL ··· COMPLETE

A3 ORIGINAL ··· COMPLETE (or "ERROR at 

PD1 PD2

...")

SIMULATION 41-3

PD SENSOR DATA DISPLAY.

OCSW

PD1[128]: 200     PD2[128]: 200

PD3[128]:  50     PD4[128]:  52

PD5[128]:  51     PD6[128]:  50

PD7[128]:  52

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments