Sharp AR-M550N Service Manual Download Page 280

Page: 280 / 460

: Feb. 9 2004

AR-M550/M620/M700 SIMULATION 8 - 22

( ) : Added when the punch unit is installed.

< > : Added when the saddle unit is installed.

Operation/Procedure

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press START key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the load.

(When the punch unit is installed)

(When the saddle unit is installed.)

Operation/Procedure

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key. (The entered value is stored.)

PI19

Tray lift motor clock detection 2

PI19S

Saddle No. 2 paper detection

When the saddle unit is
installed

PI20

Oscillation guide clock detection

PI20S

Saddle No. 3 paper detection

When the saddle unit is
installed

PI21

Staple lead edge detection

PI21S

Paper folding HP detection

When the saddle unit is
installed

PI22

Staple dive HP detection

PI23

Tray 2 lift motor clock detection 1

PI24

Tray 2 lift motor clock detection 2

PI25

Tray 2 HP detection

MS1

Front door / Upper door open
detection

MS1S

Saddle entry port door detection

When the saddle unit is
installed

MS2

Oscillation guide close detection

MS2P

Punch front door open detection

When the punch unit is
installed

MS2S

Front door open detection

When the saddle unit is
installed

MS3

Safety area detection

MS3S

Paper exit door open detection

When the saddle unit is
installed

MS4

Shutter close detection

MS4S

Saddle staple presence detection
2

When the saddle unit is
installed

MS5S

Stitch operation HP detection 2

When the saddle unit is
installed

MS6S

Saddle staple presence detection
1

When the saddle unit is
installed

MS7

Cartridge detection

MS7S

Stitch operation HP detection 1

When the saddle unit is
installed

MS8

Staple empty detection

MS9

Tray approaching detection

3-3

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of the load in the finisher
and the control circuit.

Section

Finisher

Item

Operation

SL7

Belt wait solenoid

SL6

Wait solenoid

SIMULATION 3-2

FINISHER SENSOR CHECK.

PI10 PI20 PI19 PI9 PI22

PI1

PI14 PI3

PI17 PI12 PI11

MS8

PI21 MS7

PI18

PI5

PI8 PI6 PI7 MS2 MS4 MS1 MS3 PI16

PI15 MS9 PI24 PI23 PI25

(PI2P) (MS2P) (PI1P) (PI3P)

SL5

Paddle solenoid

SL3

Buffer exit port solenoid

SL2

Buffer entry port solenoid

SL1

Flapper solenoid

M10

Tray 2 lift motor

Entry port transport motor

No. 2 transport motor

Oscillation motor

Staple motor

Tray 1 lift motor

Stapler shift motor

Alignment motor

Paper exit motor

No. 1 transport motor

M2P

Punch side resist motor

M1P

Punch motor

SL4S

Transport plate contact solenoid

SL2S

No. 2 paper deflection plate solenoid

SL1S

No. 1 paper deflection plate solenoid

M8S

Paper holding motor

M7S

Stitch motor: Front

M6S

Stitch motor: Rear

M5S

Saddle alignment motor

M4S

Paper positioning motor

M3S

Guide motor

M2S

Paper folding motor

M1S

Saddle transport motor

Press [START] key, and the operation
is started.

Press [CUSTOM SETTINGS] key, and the
operation is stopped.

3-10

Purpose

Adjustment

Function
(Purpose)

Finisher (AR-F16) adjustment

Section

Finisher

Item

Operation

Item

Set range

Saddle stitch/folding position
adjustment

192 - 208, 1STEP: 0.25 mm

Alignment position adjustment

2 - 18, 1STEP: 0.35 mm

Staple binding position
adjustment

68 - 132, 1STEP: 0.152 mm

Punch center adjustment

37 - 63, 1STEP: 0.15mm

SIMULATION 3-3

FINISHER LOAD TEST. SELECT 1-

AND PRESS START.

SIMULATION 3-3

FINISHER LOAD TEST. EXECUTING

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 280 / 460

Search results

Summary of Contents for AR-M550N

Reviews: