Sharp AR-M550N Service Manual Download Page 322

Page: 322 / 460

: Feb. 9 2004

AR-M550/M620/M700 SIMULATION 8 - 64

Operation/Procedure

1) Enter the sharpness level with 10-key.

2) Press [START] key.

The greater the adjustment value is, the greater the sharpness is.

Default: 3 (Normal), 1 (Halftone)

Operation/Procedure

1) Select the number corresponding to one of the following adjust-

ment items with 10-key. (Select one of 0 - 11.)

∗

Normal mode (Image density adjustment level)

∗

Normal mode (Image density adjustment level) (Half-tone mode)

∗

Auto mode

∗

Auto mode (Half-tone mode)

2) Press [START] key.

3) Enter the image density adjustment value with 10-key.

4) Press [START] key or press [P] key.

The adjustment value is set.

Operation/Procedure

(Adjustment mode selection)

1) Select the number corresponding to the copy mode to be adjusted

with 10-key. (Select one of 3 - 7.)

2) Press [START] key.

(Copy magnification ratio adjustment)

1) Select the number corresponding to the copy magnification ratio

adjustment mode to be adjusted with 10-key. (Select one of 3 - 7.)

2) Press [START] key.

3) Enter the copy magnification ratio adjustment value with 10-key.

4) Press [P] key or [START] key.

When the [START] key is pressed, copying is performed and the
adjustment value is set simultaneously.

The copy magnification ratio in the sub scan direction can be
adjusted by changing the scan speed (motor RPM).

46-39

Purpose

Adjustment

Function
(Purpose)

Used to adjust sharpness of the FAX mode.

Section

Item

Picture quality

Press [START] key.

Press [CUSTOM SETTINGS] key.

46-45

Purpose

Adjustment

Function
(Purpose)

Used to adjust the image density in the FAX mode
(600dpi).

Section

Item

Picture quality

Item

Set

range

Default

AUTO

Auto

0 - 99

1.0

Exposure level 1

2.0

Exposure level 2

3.0

Exposure level 3

4.0

Exposure level 4

5.0

Exposure level 5

AUTO (H)

Auto (Half-tone)

1.0 (H)

Exposure level 1 (Half-tone)

2.0 (H)

Exposure level 2 (Half-tone)

3.0 (H)

Exposure level 3 (Half-tone)

4.0 (H)

Exposure level 4 (Half-tone)

5.0 (H)

Exposure level 5 (Half-tone)

SIMULATION 46-39
FAX SHARPNESS LEVEL SETUP. SELECT 1-12, AND PRESS
START.
1:OC_NORMAL

2:OC_FINE

3:OC_FINE(H)

4:OC_SFINE

5:OC_SFINE(H)

6:OC_UFINE

7:OC_UFINE(H)

8:OC_600

9:OC_600(H)

10:SPF1_NORMAL

11:SPF1_FINE

12:SPF1_FINE(H)

13:SPF1_SFINE

14:SPF1_SFINE(H)

15:SPF1_UFINE

16:SPF1_UFINE(H)

17:SPF1_600

18:SPF1_600(H)

19:SPF2_NORMAL

20:SPF2_FINE

21:SPF2_FINE(H)

22:SPF2_SFINE

23:SPF2_SFINE(H)

24:SPF2_UFINE

25:SPF2_UFINE(H)

26:SPF2_600

27:SPF2_600(H)

28:CIS_NORMAL

29:CIS_FINE

30:CIS_FINE(H)

31:CIS_SFINE

32:CIS_SFINE(H)

33:CIS_UFINE

34:CIS_UFINE(H)

35:CIS_600

36:CIS_600(H)

SIMULATION 46-39

FAX SHARPNESS LEVEL SETUP. INPUT VALUE 1-3, AND PRESS

START.

1:OC_NORMAL

Press [START] key.

Press [CUSTOM SETTINGS] key.

48-1

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy magnification ratio (in the main
scanning and the sub scanning directions).

Section

Optical (Image scanning)

Item

Picture quality

Item

Set

range

Default

0 TRAY SELECT

Paper feed tray selection

0 - 99

1 COPY START

Copy START (Default)

2 MAGNIFICATION Print magnification ratio
3 CCD (MAIN)

SCAN main scanning
magnification ratio
adjustment (CCD)

4 CCD (SUB)

SCAN sub scanning
magnification ratio
adjustment (CCD)

5 SPF (SUB)

SPF front surface
magnification ratio
adjustment (Sub scan)

6 CIS (MAIN)

SPF back surface
magnification ratio
adjustment (CIS main scan)

7 SPF (MAIN)

SPF front surface
magnification ratio
adjustment (Main scan)

Normal display

NOW COPYING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

SIMULATION 46-45

EXP.LEVEL SETUP SCANNER(600dpi). SELECT 0-5,AND PRESS

START.

0.AUTO

1.1.0

2.2.0

3.3.0

4.4.0

5.5.0

6.AUTO(H)

7.1.0(H)

8.2.0(H)

9.3.0(H)

10.4.0(H)

11.5.0(H)

SIMULATION 46-45

EXP.LEVEL SETUP SCANNER(600dpi). INPUT VALUE 0-99, AND

PRESS START.

0.AUTO

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 322 / 460

Search results

Summary of Contents for AR-M550N

Reviews: