manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 324 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 324

AR-M550/M620/M700  SIMULATION  8 - 66

∗

Set DENA to 35. (Enter 35 as the adjustment value of DENA,
and press [P] key.) (0.1mm/step)

2) Make a copy at the normal ratio (100%) and check the lead edge

void area and the image loss. (Enter 100 as the set value of the
copy magnification ratio (MAGNIFICATION), and press [START}
key.)

3) If the adjustment result is not satisfactory, perform the following

procedures.

∗

If the lead edge void are is not 3.5mm:
Change the adjustment value of RRCB and perform the adjust-
ment. (Change the adjustment value of RRCB and press
[START] key.) (1msec/step)

∗

If the lead edge image loss is not 1.5mm:
Change the adjustment value of RRCA and perform the adjust-
ment. (Change the adjustment value of RRCA and press
[START] key.)
(Shift for the adjustment value change: 0.2mm/step)

(Rear edge void area adjustment)

Adjust so that the rear edge void area is 3.5mm. (Change the adjust-
ment value of TRAIL EDGE, and press [START] key.)

(Front/rear frame direction image loss adjustment)

Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment
value of SIDE, and press [P] key.)

When the adjustment value is changed, the image position is shifted in
the front/rear frame direction.

(Front/rear frame direction void area adjustment)

Adjust so that the total of the front/rear direction void areas is 7.0mm.
(Change the adjustment values of FRONT/REAR, and press [START]
key.)

Front frame void area = 3.5mm

Rear frame void area = 3.5mm

If, as shown above, the front and the rear void areas are not even, use
SIM 50-5 to adjust the image off-center position.

NOTE: When [P] is pressed after entering an adjustment value, the

adjustment value is set. When [START] key is pressed instead,
the adjustment value is set and copying is performed.)

(Copy condition in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key.

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray of the tar-

get paper with 10-key. 

4) Press [START] key. (The paper feed tray is selected.)

∗

To set the magnification ratio, perform the following procedure.

1) Enter 2 with 10-key.

2) Press [START] key.

3) Enter the copy magnification ratio with 10-key.

4) Press [START] key.

Item

Content

Set 

range

Default

0 TRAY SELECT

Paper feed tray selection

1 - 6

–

1 COPY START

Copy START (Default)

–

–

2 MAGNIFICATION

Print magnification ratio

25 - 

400%

–

(Lead edge adjustment value)

3 RRCA

Document scan start 
position

0 - 99

50

4 RRCB

Resist roller clutch ON 
timing adjustment value

10 SIDE2 ADJ.

Correction value for 
RRCB in the back 
surface print mode

1 - 99

50

(Image loss set value)

5 LEAD

Lead edge image loss 
set value

0 - 99

15

6 SIDE

Side image loss set 
value

20

(Void set value)

7 LEAD_EDGE 

(DENA) 

Lead edge void set value

0 - 99

35

8 TRAIL_EDGE 

(DENB) 

Rear edge void 
adjustment value

9 FRONT/REAR

Front/Rear void 
adjustment value

Normal display

NOW COPYING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

1

TRAY1

TRAY1

2

TRAY2

TRAY2

3

TRAY3

TRAY3

4

TRAY4

TRAY4

5

BPT

Manual feed

6

LCC

Side LCC

Set range

25 - 400 (%)

Select 2, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

50

1

2

Press [CUSTOM SETTINGS] key.

Press [START] key. 

Press [CUSTOM SETTINGS] key, 
or terminate copying.

Press [START] key or 
press [CUSTOM SETTINGS] key. 

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS

START.

3.RRCA

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. NOW COPYING.

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. SELECT 1-6, AND PRESS START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

Select 1, and 
press [START] key.

Select 0, and press [START] key.

Select other than 0 - 2, and press [START] key. 

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START.

0.TRAY SELECT 

1

   1.COPY START

2.MAGNIFICATION 

100

(ADJUSTMENT DATA) 3.RRCA 

50

 4.RRCB 

50 

10.SIDE2 ADJ. 

50

(IMAGE LOSS SETTING) 5.LEAD 

15

 6.SIDE 

20

(VOID SETTING) 7.LEAD_EDGE(DENA) 

50

             8.TRAIL_EDGE(DENB) 

30

  9.FRONT/REAR 

30

100

SIMULATION 50-1

LEAD EDGE ADJUSTMENT.

(MAGNIFICATION)

  INPUT 25-400(%)

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments