Sharp AR-M550N Service Manual Download Page 79

Page: 79 / 460

: Feb. 6 2004

AR-M550/M620/M700 DETAILS OF EACH SECTION 6 - 24

C. Maintenance and parts replacement

(1) Maintenance list

: Check (Clean, replace, or adjust as necessary.)

❍

: Clean

▲

: Replace

∆

: Adjust

✩

: Lubricate

❏

: Shift position

(2) Maintenance and parts replacement

(List of Replacement Parts)

AR-M550U/N (PM: 250K)

When

calling

250K 500K 750K 1000K 1250K 1500K 1750K 2000K

Remark

AR-M620U/N, AR-M700U/N
(PM: 300k)

300K 600K 900K 1200K 1500K 1800K 2100K 2400K

Unit name No.

Part name

Paper Feed
Trays 3 and
4

Pickup roller

(Note 1)

Paper feed roller

(Note 1)

Separation roller

(Note 1)

Torque limiter

(Note 1)

(Note 1) Replacement reference: For replacement, refer to each paper feed port counter value.

Torque limiter: 800K (However, 400K for manual paper feed section)

Paper feed tray 3/4, paper feed unit section: 100K or 1 year

No.

Unit

Parts

Paper feed tray units 3
and 4

Pickup roller

Paper feed roller

Separation roller

Torque limiter

Paper pickup solenoid

Paper feed tray upper limit
detector

Paper feed tray empty
detector

Transport roller 8, 10

Transport roller 5, 7

Paper pass detector

Others

Paper size detection PWB

Paper remaining quantity
detector

Paper feed tray paper
width detector

Dry heater

a-9

a-4

a-5

a-10

a-8

b-3

b-2

b-4

b-1

a-7 a-6

a-1

a-2 a-3

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 79 / 460

Search results

Summary of Contents for AR-M550N

Reviews: