manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 323 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 323

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 65

The greater the value is, the greater the correction is. One step corre-
sponds to 0.1% adjustment.

(Copy condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key.

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray of the

selected paper with 10-key. (Select one of 1 - 6.)

4) Press [START] key. (The paper feed tray is selected.)

When the total of the above set value (1 - 6) and 10 is entered, the
mode is changed to the duplex mode.

∗

The copy magnification ratio can be set with the following

1) Enter 2 with 10-key.

2) Press [START] key.

3) Enter the copy magnification ratio with 10-key.

4) Press [START] key.

NOTE: When [P] key is pressed after entering the adjustment value,

the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is performed.

Operation/Procedure

When the sub scanning direction image magnification ratio adjustment
with SIM 48-1 cannot provide a satisfactory result if a different magnifi-
cation ration is set and a copy is made, perform this simulation.

When there is an error in the copy magnification ratio in reduction
copy, change the adjustment value of the high speed mode. When
there is an error in the copy magnification ratio in enlargement copy,
change the adjustment value of the low speed mode.

1) Select the number corresponding to the adjustment mode with 10-

key.

2) Press [START] key.

3) Enter the copy adjustment value with 10-key.

The scanner/SPF motor rotation sped adjustment value is entered.

4) Press [START] key.

Operation/Procedure

(Lead edge image loss/void area adjustment)

1) Set the lead edge image loss adjustment value (LEAD EDGE) and

the paper lead edge void adjustment value (DENA) as follows. 

(Standard set value) Lead edge image loss: 1.5mm (LEDA: 15)

Paper lead edge void: 3.5mm (DENA: 35)

∗

Set LEAD to 15. (Enter 15 as the adjustment value of LEAD, and
press [P] key.) (0.1mm/step)

1

TRAY1

TRAY1

2

TRAY2

TRAY2

3

TRAY3

TRAY3

4

TRAY4

TRAY4

5

BPT

Manual feed

6

LCC

Side LCC

Set range

25 - 400%

Select 2, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

50

1

2

Select other than 0 - 2, 
and press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key. 

Press [CUSTOM SETTINGS] key, 
or terminate copying.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START.

0.TRAY SELECT 

1

 1.PRINT START

2.MAGNIFICATION 

100

3.CCD(MAIN) 

50

 4.CCD(SUB) 

50

 5.SPF(SUB) 

50

6.CIS(MAIN) 

50

 7.SPF(MAIN) 

50

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS

START.

4.CCD(SUB)

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. NOW COPYING.

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

   (ABOVE+10: DUPLEX MODE)

Select 1, and 
press [START] key. 

Select 0, and press [START] key.

1

1

100

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT.

(MAGNIFICATION)

  INPUT 25-400(%)

48-5

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy magnification ratio in the sub 
scanning direction. 

Section

Optical (Image scanning)

Item

Picture quality

Item

Content

Set 

range

Default

0

MIR (220)

Mirror motor (220mm/sec)

0 - 99

50

1

MIR (110)

Mirror motor (110mm/sec)

2

SPF (360)

SPF motor (360mm/sec)

3

SPF (220)

SPF motor (220mm/sec)

4

SPF (110)

SPF motor (110mm/sec)

Select other than 0 - 5, and 
press [START] key.

Press [START] key, or press 
[CUSTOM SETTINGS] key.

50

50-1

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy image position and the void 
area (image loss) adjustment on print paper in the 
copy mode. (The similar adjustment can be performed 
with SIM 50-5 and 50-2 (Simplified method).) 
(Document table mode)

Section
Item

Picture quality

Image position

0

SIMULATION 48-5

MOTOR SPEED ADJUSTMENT. SELECT 0-4, AND PRESS START.

0.MIR(220) 

50

    1.MIR(110) 

50

2.SPF(360) 

50

    3.SPF(220) 

50

 

4.SPF(110) 

50

50

SIMULATION 48-5

SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND

PRESS START.

0.MIR(220)

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments