manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 334 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 334

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 76

Operation/Procedure

1) Select 2 with 10-key.

2) Press [START] key. 

3) Enter the adjustment value with 10key. (1 count: 0.1mm)

4) Press [START] key.

Operation/Procedure

This simulation is used to change and check the engine soft SW. Set
this setting to the default.

There is no need to change this setting in the market.

Operation/Procedure

This simulation is used to change and check the scanner soft SW. Set
this setting to the default.

There is no need to change this setting in the market.

Operation/Procedure

This simulation is used to change and check the controller soft SW. Set
this setting to the default.

There is no need to change this setting in the market.

Operation/Procedure

1) Select the number corresponding to the data transfer mode with

10-key.

53-8

Purpose

Adjustment

Function
(Purpose)

Used to adjust the document scan start position. (Used 
to adjust the scanner scan position in the SPF mode 
front scan.)

Section
Item

Item

Set 

range

Default

2

MANUAL

Manual feed adjustment (Direct 
entry of a number)

1 - 70

32

Select 2, and 
press [START] key. 

Press [START] key, or 
press [CUSTOM SETTINGS] key.

55

55-1

Purpose

Setting

Function
(Purpose)

Used to set the specifications of the engine control 
operations. (PCU PWB)

Section

Item

Operation Specifications

Press [START] key.

Press [CUSTOM SETTINGS] key or [START] key.

1

SIMULATION 53-8

SPF SCANNING POSITION ADJUSTMENT. PRESS START.

2.MANUAL   

25

1

25

SIMULATION 53-8

SPF SCANNING POSITION ADJUSTMENT. INPUT VALUE 1-70, AND

PRESS START.

2.MANUAL

1

SIMULATION 55-1

ENGINNE SOFT SW. SETTING. SELECT 1-16, AND PRESS START.

1 2 3 4 5 6 7 8

0 0 0 0 1 0 0 1

SIMULATION 55-1

ENGINNE SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS

START.

    SOFT SW-1:

55-2

Purpose

Setting

Function
(Purpose)

Used to set the specifications of the scanner control 
operations. (Scanner control PWB)

Section

Item

Operation Specifications

Press [START] key.

Press [CUSTOM SETTINGS] key or [START] key.

55-3

Purpose

Setting

Function
(Purpose)

Used to set the specifications of the controller 
operations. (MFP control PWB)

Section
Item

Operation Specifications

Press [START] key.

Press [CUSTOM SETTINGS] key or [START] key.

56

56-1

Purpose

Data transfer

Function
(Purpose)

Used to transfer the MFP controller data. (Used to 
repair the PWB.)

Section

MFP controller

Item

Data transfer

1

SIMULATION 55-2

SCANNER SOFT SW. SETTING. SELECT 1-16, AND PRESS START.

1 2 3 4 5 6 7 8

0 0 0 0 1 0 0 1

SIMULATION 55-2

SCANNER SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS

START.

    SOFT SW-1:

1

SIMULATION 55-3

MFP SOFT SW. SETTING. SELECT 1-16, AND PRESS START.

1 2 3 4 5 6 7 8

0 0 0 0 1 0 0 1

SIMULATION 55-3

MFP SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS

START.

    SOFT SW-1:

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments