Sharp AR-M550N Service Manual Download Page 329

Page: 329 / 460

AR-M550/M620/M700 SIMULATION 8 - 71

5) Enter the above values as the set values of L4 and L5. (Enter the

adjustment values of L4 and L5, and press [P] key.)

(The image scan start timing is determined with the detection tim-
ing of the document lead edge by the detector SPPD4.)

If the adjustment result is not satisfactory, perform the above proce-
dures again or adjust with SIM 50-1.

NOTE: If the adjustment result of the above procedures is not satisfac-

tory, though the adjustment value is changed individually, the
adjustment cannot be completed normally.

Repeat procedures 2) - 6) until a satisfactory result is obtained.

(Rear edge image loss adjustment)

Adjust so that the rear edge image loss is 3.5mm. (Change the adjust-
ment value of TRAIL EDGE, and press [START] key.)

(Front/rear frame direction image loss adjustment)

Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment
value of SIDE, and press [P] key.)

When the adjustment value is changed, the image position is shifted in
the front/rear frame direction.

NOTE: When [P] key is pressed after entering the adjustment value,

the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is performed.
(Table 2)

(Copy condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key.

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray to be used

with 10-key. (Table 3)

4) Press [START] key. (The paper feed tray is selected.)

∗

To set the copy magnification ratio, perform the following procedure.

1) Enter 2 with 10-key.

2) Press [START] key.

3) Enter the copy magnification ratio with 10-key.

4) Press [START] key.

(Table 1)

(Table 2)

(Table 3)

When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.

L5 = Distance (mm) from the image lead edge position to the

paper lead edge x 10

Set range

25 - 200 (%)

Item

Set

range

Default

TRAY SELECT

Paper feed tray selection
(1 - 6)

–

COPY START

Copy START (Default)

–

MAGNIFICATION Print magnification ratio

(25 - 200%)

–

(Lead edge adjustment value)

Distance from the front
surface image lead edge
to the scale of 10mm
(SPF: 200%)

0 - 999

–

Distance from the back
surface image lead edge
to the scale of 10mm
(SPF: 200%)

–

(Image loss set value: SIDE 1)

LEAD_EDGE

Front surface lead edge
image loss set value

0 - 99

FRONT_REAR

Front surface side edge
image loss set value

TRAIL_EDGE

Front surface rear edge
image loss set value

0 - 20

(Image loss set value: SIDE 2)

LEAD_EDGE

Back surface lead edge
image loss set value

0 - 99

FRONT/REAR

Back surface side edge
image loss set value

10 TRAIL_EDGE

Back surface rear edge
image loss set value

0 - 20

Normal display

NOW COPYING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

TRAY1

TRAY2

TRAY3

TRAY4

BPT

Manual feed

LCC

Side LCC

Select 2, and
press [START] key.

Press [START] key, or
press [CUSTOM SETTINGS] key.

Item

Set

range

Default

SIMULATION 50-7

LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS

START.

0.TRAY SELECT

1.COPY START

2.MAGNIFICATION

200

(ADJUSTMENT DATA) 3.L4

160

4.L5

160

(IMAGE LOSS SETTING)

SIDE1: 5.LEAD_EDGE

6.FRONT/REAR

7.TRAIL_EDGE

SIDE2: 8.LEAD_EDGE

9.FRONT/REAR

10.TRAIL_EDGE

Press [CUSTOM SETTING] key.

Press [START] key.

Press [CUSTOM SETTINGS] key,
or terminate copying.

Press [START] key or
press [CUSTOM SETTINGS] key.

SIMULATION 50-7

LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND

PRESS START.

3.L4

SIMULATION 50-7

LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.

SIMULATION 50-7

LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-16, AND PRESS

START.

(FEED TRAY)

1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

5.BPT 6.LCC

Select 1,
and press
[START] key.

Select 0, and press [START] key.

Select other than 0 - 2, and press [START] key.

100

SIMULATION 50-7

LEAD EDGE ADJUSTMENT(SPF CALC.).

(MAGNIFICATION)

INPUT 25-200(%)

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 329 / 460

Search results

Summary of Contents for AR-M550N

Reviews: