Sharp AR-M550N Service Manual Download Page 234

Page: 234 / 460

: Feb. 9 2004

AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 19

1) On the SPF original tray, place such a duplex original as illustrated

below.

2) Make a normal duplex copy on A4 paper.

3) Measure the lengths of the copied image (on the back side) and

the original image.

4) Determine the image magnification factor using the following for-

mula:

Image magnification factor (%) = Copy dimension/original dimen-
sion x 100

Image magnification factor (%) = 99 / 100 x 100 = 99

If the image magnification factor is within the spec (100±0.8%), no
adjustment is required; otherwise, do the following steps.

5) Go through the modes specified in Simulation 48-1.

6) Select the number that corresponds to the adjustment item CIS

(MAIN) using the numeric keypad.

7) Press the Start key

8) Adjust the image magnification factor by entering an appropriate

value through the numeric keypad.

9) Press the P or Start key

Pressing the Start key starts copy operation as well as applying the
adjustment value.

Repeat the above adjustments until an acceptable result is obtained.

A4 size

(both sides)

10mm

original

100

150

200

250

copy

100

150

200

250

Select 2, and
press [START] key.

Press [START] key, or
press [CUSTOM SETTINGS] key.

This adjustment item is intended to adjust the image magnification
in the main scanning direction in SPF back-face mode (CIS). (CIS
(MAIN))

Select other than 0 - 2,
and press [START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key,
or terminate copying.

Press [START] key, or
press [CUSTOM SETTINGS] key.

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START.

0.TRAY SELECT

1.PRINT START

2.MAGNIFICATION

100

3.CCD(MAIN)

4.CCD(SUB)

5.SPF(SUB)

6.CIS(MAIN)

7.SPF(MAIN)

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS

START.

4.CCD(SUB)

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. NOW COPYING.

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START.

(FEED TRAY)

1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

5.BPT 6.LCC

(ABOVE+10: DUPLEX MODE)

Select 1, and
press [START] key.

Select 0, and press [START] key.

100

SIMULATION 48-1

MAGNIFICATION ADJUSTMENT.

(MAGNIFICATION)

INPUT 25-400(%)

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 234 / 460

Search results

Summary of Contents for AR-M550N

Reviews: