manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 282 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 282

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 24

Operation/Procedure

The operating conditions of the sensors and detectors are displayed.

The active sensors and detectors are highlighted.

<LCC>

Operation/Procedure

1.

Select the number corresponding to the target of operation check
with 10-key.

2.

Press [START] key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the load.

<Side LCC>

Operation/Procedure

The LCD is changed as shown below. (The contrast changes every
2sec from the current level to MAX 

→

 MIN 

→

 the current level. During

this period, each LED is lighted.

Operation/Procedure

1) Select the number corresponding to the target of operation check

with 10-key.

2) Press [START] key.

The load selected in procedure 1 performs ON/OFF operation.

Press [CUSTOM SETTINGS] key to stop the operation of the load.

The ON/OFF operation of the selected heater lamp is repeated
every 500ms five times.

4

4-2

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operations of the sensors and 
detectors in the paper feed section (large capacity tray) 
and the related circuit.

Section

Paper feed

Item

Operation

LTD

Transport sensor

LUD

Tray upper limit sensor

LLD

Tray lower limit sensor

LPED

Tray paper presence/empty sensor 

LTOD

Main unit connection detection sensor

LCD

Tray insertion detection

LOSW

Upper open/close detection SW

LRE

Lift motor encoder sensor

+24VM

24V power monitor

LLSW

Upper limit SW

4-3

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operations of the loads in the paper 
feed section (large capacity tray) and the related 
circuit.

Section

Paper feed

Item

Operation

1

LTM

LCC transport motor

2

LLM

LCC lift motor

3

LPFCL

Paper feed clutch 

4

LPSL

LCC paper feed clutch

5

LTCL

LCC transport clutch

6

LTLSL

Tray lock solenoid D

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.

SIMULATION 4-2
LCC SENSOR CHECK.
LTD         LUD         LLD         LPED
LCD         LOSW        LRE         +24VM
LLSW

SIMULATION 4-3

LCC LOAD TEST. SELECT 1-6, AND PRESS START.

1.LTM                   2.LLM

3.LPFCL                 4.LPSL

5.LTCL                  6.LTLSL

    2

SIMULATION 4-3

LCC LOAD TEST. EXECUTING....

1. LTM                  2. LLM

3. LPFCL                4. LPSL

5. LTCL                 6. LTLSL

    2

5

5-1

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of the display, LCD in the 
operation panel, and control circuit.

Section

Operation (Display/Operation key)

Item

Operation

After 6.0sec

Press [CUSTOM SETTINGS] key, 
and the operation is stopped.

5-2

Purpose

Operation test/Check

Function
(Purpose)

Used to check the operation of the heater lamp and the 
control circuit.

Section

Fixing (Fusing)

Item

Operation

1

HL1 (LOWER)

Heater lamp 1 (Lower)

2

HL2 (UPPER)

Heater lamp 2 (Upper)

3

HL3 (LEFT)

Heater lamp 3 (Left)

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.
The operation is repeated the specified 
number of times before stopping.

SIMULATION 5-1

SIMULATION 5-1

SIMULATION 5-2

HEATER LAMP TEST. SELECT 1-3 ,AND PRESS START.

1.HL1(LOWER)

2.HL2(UPPER)

3.HL3(LEFT)

    2

SIMULATION 5-2

HEATER LAMP TEST. EXECUTING···.

1.HL1(LOWER)

2.HL2(UPPER)

3.HL3(LEFT)

    2

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments