Sharp AR-M550N Service Manual Download Page 382

Page: 382 / 460

AR-M550/M620/M700 SELF DIAG MESSAGE AND TROUBLESHOOTING 9 - 27

Main
code

Sub

code

Title

FAX expansion Flash memory
trouble (MFP control detection)

Phenomenon

Display

Lamp
Message

Details

FAX expansion Flash
memory trouble (MFP
control detection)
The expansion flash
memory inserted to the
FAX I/F PWB could not
be cleared.

Section

FAX

Operation
mode
Note

Case 1

Trouble
position/
Cause

Initialization of the FAX
expansion memory failed,
which is required for a
new memory that is
inserted to the PWB.

Remedy

Use SIM 66-10 to clear
the expansion flash
memory.

Note

Main
code

Sub

code

Title

FAX modem operation abnormality

Phenomenon

Display

Lamp

Message

Details

FAX modem operation
abnormality
The initializing process of
the modem chip in the
FAX PWB is not
completed normally.

Section

FAX

Operation
mode

Note

Case 1

Trouble
position/
Cause

SW101 in the FAX PWB
tries to perform normal
operation on the boot
side.

Remedy

Set SW101 on the FAX
PWB to other than the
boot side, and turn on the
power again.

Note

Case 2

Trouble
position/
Cause

FAX PWB modem chip
operation trouble

Remedy

Replace the FAX PWB.

Note

Main
code

Sub

code

Title

FAX write protect cancel

Phenomenon

Display

Lamp
Message

Details

The write protect jumper
of the FAX interface PWB
is released.

Section

FAX

Operation
mode

Note

Case 1

Trouble
position/
Cause

The FAX write protect pin
is set to Write Enable.

Remedy

Check the write protect
pin in the FAX interface
PWB.

Note

Case 2

Trouble
position/
Cause

FAX interface PWB
trouble
FAX PWB trouble

Remedy

Replace the FAX PWB.
Replace the FAX
interface PWB.

Note

Main
code

Sub

code

Title

Abnormal combination of the TEL/
LIU PWB and the FAX soft switch

Phenomenon

Display

Lamp
Message

Details

Combination error of TEL/
LIU PWB and software
If the destination of the
installed TEL/LIU PWB
differs from that of the
FAX soft switch, it is
judged as an error.

Section

FAX

Operation
mode
Note

Case 1

Trouble
position/
Cause

The destination of the
installed TEL/LIU PWB
differs.
The FAX PWB
information (soft switch)
differs.

Remedy

Check the destination of
the TEL/LIU PWB.
Check the FAX PWB
information (soft switch).

Note

Case 2

Trouble
position/
Cause

TEL/LIU PWB trouble

Remedy

Replace the TEL/LIU
PWB.

Note

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 382 / 460

Search results

Summary of Contents for AR-M550N

Reviews: