manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 66 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 66

: Feb. 6 2004

1

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 11

4) Remove the manual feed gate solenoid.

a-8. Manual feed paper pass detector 1

1) Remove the multi manual paper feed tray unit. (See “a. Multi man-

ual paper feed tray unit”)

2) Remove the bottom cover. (See “a-6. Torque limiter”)

3) Disconnect the connector, and remove the manual paper feed

paper pass detector 1.

a-9. Paper feed clutch

1) Remove the multi manual paper feed tray unit. (See “a. Multi man-

ual paper feed tray unit”)

2) Remove the upper cover. (See “a-3. Pickup roller”)

3) Remove the front cover.

4) Remove the interface pass earth plate, the E-ring, and the bearing,

and remove the manual paper feed mounting plate. 

5) Remove the connector and the E-ring, and remove the paper feed

clutch. 

∗

When assembling, fit the rotation stopper of the paper feed clutch
with the clutch fixing screw.

a-10. Paper pickup solenoid

1) Remove the multi manual paper feed tray unit. (See “a. Multi man-

ual paper feed tray unit”)

2) Remove the manual paper feed upper cover and the pickup upper

cover. (See “a-3. Pickup roller”)

3) Remove the front cover, and remove the manual paper feed

mounting plate. (See “a-9. Paper feed clutch”)

4) Remove the spring.

5) Disconnect the connector, and remove the paper pickup solenoid

unit.

6) Remove the paper pickup solenoid.

∗

When assembling, tighten the screw so that the lever tip is at
13±0.5mm from the frame edge with the solenoid plunger pulled.

1

13   5mm

(Note for assembly)

Check that there is a clearance when the solenoid plunger is pulled.

1

4.2mm

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments