manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 176 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 176

: Feb. 6 2004

1

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 121

(2) Maintenance and parts replacement

(Replacement parts)

a. Paper feed unit

1)

Remove the cabinet. 

(See  “a-1. Cabinet” in the previous section,

“[External outfit section]”)

2) Disconnect the connector, and remove the paper feed unit.

a-1. Paper feed roller

a-2. Pickup roller

1) Pull up the lever and open the upper cover.

2) Remove the roller cover.

3) Remove the pawl and remove the rollers.

a-3. SPF paper feed clutch

a-4. SPF document tray upper limit detector

a-5. SPF document upper limit detector

a-6. SPF cover switch

a-7. SPF document paper pass detector 1

1) Remove the cabinet. (See “a-2. Document mat” in the previous

section, “[External outfit section]”)

2) Remove the document feed tray unit. (See “a. Paper feed unit” in

this section)

No.

Unit

Parts

a

Paper feed 
unit

1

Document feed roller

✕

2

Pickup roller

✕

3

SPF paper feed clutch

4

SPF document tray upper limit 
detector

5

SPF document upper limit 
detector

6

SPF cover switch

7

SPF document paper pass 
detector 1

b

1

Separation roller

✕

2

SPF paper feed/paper transport 
motor

3

SPF resist roller brake clutch

4

SPF resist roller clutch

5

No. 1 resist roller (Drive)

❍

6

Torque limiter

✕

7

SPF paper transport roller 2 
brake clutch

8

SPF paper transport roller 2 
clutch

9

Transfer roller 2 (Drive)

❍

10

Transport roller 1 (Drive)

❍

11

SPF document paper pass 
detector 2

1

1

a

a-1

a-2 a-4 a-5 a-6 a-7 a-3

b-1

b-2

b-4

b-7

b-6

b-8

b-5

b-9

b-10

b-11

b-3

3) Remove the cover and disconnect the connector.

A

B

1

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments