![Mitsubishi Electric MELSEC-L LD75D User Manual Download Page 453](http://html.mh-extra.com/html/mitsubishi-electric/melsec-l-ld75d/melsec-l-ld75d_user-manual_238753453.webp)
451
CHAPTER 9 MAJOR POSITIONING CONTROL
9
9.
2 Set
ting t
he Pos
itioning
D
at
a
9.2.22
NOP instruction
The NOP instruction is used for the nonexecutable control system.
(1) Operation
The positioning data No. to which the NOP instruction is set transfers, without any processing, to the operation for
the next positioning data No.
(2) Positioning data setting example
The following table shows the setting examples when "NOP instruction" is set in positioning data No. 1 of axis 1.
Refer to
Page 152, Section 5.3 for information on the setting details.
(3) Restrictions
The error "Control system setting error" (error code: 524) will occur if the "NOP instruction" is set for the control
system of the positioning data No. 600.
<Use example of NOP instruction>
If there is a possibility of speed switching or temporary stop (automatic deceleration) at a point between two points during
positioning, that data can be reserved with the NOP instruction to change the data merely by the replacement of the
identifier.
Setting item
Setting example
Setting details
Axis 1 positioning
data No. 1
[Da.1]
Operation pattern
Setting not required. (Setting value will be ignored.)
[Da.2]
Control system
NOP instruction
Set the NOP instruction
[Da.3]
Acceleration time No.
Setting not required. (Setting value will be ignored.)
[Da.4]
Deceleration time No.
Setting not required. (Setting value will be ignored.)
[Da.5]
Axis to be interpolated
Setting not required. (Setting value will be ignored.)
[Da.6]
Positioning address/movement
amount
Setting not required. (Setting value will be ignored.)
[Da.7]
Arc address
Setting not required. (Setting value will be ignored.)
[Da.8]
Command speed
Setting not required. (Setting value will be ignored.)
[Da.9]
Dwell time
Setting not required. (Setting value will be ignored.)
[Da.10]
M code
Setting not required. (Setting value will be ignored.)
Summary of Contents for MELSEC-L LD75D
