196
(4) [Md.23] Axis error No.
(5) [Md.24] Axis warning No.
(6) [Md.25] Valid M code
Item
Description
Storage details
When an axis error is detected, the error code corresponding to the error details is stored.
• The latest error code is always stored. (When a new axis error occurs, the error code is overwritten.)
• When "[Cd.5] Axis error reset" (axis control data) turns ON, the axis error No. is cleared (set to 0).
Reading the monitor
value
■
Monitoring is carried out with a decimal display.
For details on error No. (error codes), refer to the following.
Default value
0
Storage buffer memory
address
Axis 1: 806
Axis 2: 906
Axis 3: 1006
Axis 4: 1106
Item
Description
Storage details
Whenever an axis warning is reported, a related warning code is stored.
• This area stores the latest warning code always. (Whenever an axis warning is reported, a new warning code replaces the stored
warning code.)
• When the "[Cd.5] Axis error reset" (axis control data) is set to ON, the axis warning No. is cleared to "0".
Reading the monitor
value
■
Monitoring is carried out with a decimal display.
For details on warning No. (warning codes), refer to the following.
Default value
0
Storage buffer memory
address
Axis 1: 807
Axis 2: 907
Axis 3: 1007
Axis 4: 1107
Item
Description
Storage details
This area stores an M code that is currently active (i.e. set to the positioning data relating to the current operation).
• Update timing: turning ON of the M code ON signal
When the PLC READY signal (Y0) goes OFF, the value is set to "0".
Reading the monitor
value
■
Monitoring is carried out with a decimal display.
Default value
0
Storage buffer memory
address
Axis 1: 808
Axis 2: 908
Axis 3: 1008
Axis 4: 1108
Monitor
value
Error No.
Monitor
value
Warning No.
Monitor
value
M code No.
(0 to 65535)
Summary of Contents for MELSEC-L LD75D
