Lenovo x3650 M5 Installation And Service Manual Download Page 1151 | Manualshive

Page: 1151 / 1340

background image

•

S.3108007 The default system settings have been restored. System Configuration Restored to

Defaults

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to

this error.

•

S.3818004 The CRTM flash driver could not successfully flash the staging area. A failure occurred.

CRTM Update Failed

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Continue booting the system. If the system does not reset, manually reset the system.

2. If the error is not reported on the subsequent boot, no additional recovery action is required.

3. If the error persists, continue booting system and update the UEFI image.

4. (Trained service technician only) Replace the system board.

•

S.3818007 The firmware image capsules for both flash banks could not be verified. CRTM image

capsule could not be verified

Explanation:

Severity

Error

User Response

Complete the following steps:

1. If system failed to boot successfully, DC cycle system.

2. If system boots to F1 setup, update the UEFI image and reset bank to primary (if required). If the

system boots without error, recovery is complete and no additional action is required.

3. If system fails to boot, or if the firmware update attempt fails, (trained service technician only)

replace the system board.

•

S.51003 An uncorrectable memory error was detected in DIMM slot [arg1] on rank [arg2]. An

uncorrectable memory error was detected on processor [arg3] channel [arg4]. The failing DIMM
within the channel could not be determined. An uncorrectable memory error has been detected.
Fatal Memory Error Occurred

Explanation:

Appendix B. UEFI/POST diagnostic codes

1139

«
...
1149
1150
1151
1152
1153
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: IBM Pages: 84

Brand: IBM Pages: 110

e Server iSeries 825

Brand: IBM Pages: 52

digitalSTROM-Server

Brand: aizo Pages: 2

Brand: Sercomm Pages: 75

Brand: 7starlake Pages: 32

Brand: Shenzhen JingFeng Pages: 11

Brand: Interface Masters Pages: 34

Brand: Fujitsu Pages: 280

Proliant BL480c

Brand: HP Pages: 65

ProLiant BL420c

Brand: HP Pages: 88

Brand: HP Pages: 34

ProLiant BL685c G5

Brand: HP Pages: 23

ProLiant BL660c Gen 9

Brand: HP Pages: 3

ProLiant BL460c G7

Brand: HP Pages: 74

ProLiant BL495c G6

Brand: HP Pages: 90

ProLiant BL685c G7

Brand: HP Pages: 67

ProLiant BL280c Generation 6 (G6)

Brand: HP Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands