Lenovo x3650 M5 Installation And Service Manual Download Page 455

Page: 455 / 1340

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0215

User Response

Check storage documentation by LSI Event ID.

•

80010002-0701ffff : Numeric sensor [NumericSensorElementName] going low (lower non-critical)

has asserted. (CMOS Battery)

This message is for the use case when an implementation has detected a Lower Non-critical sensor
going low has asserted.

May also be shown as 800100020701ffff or 0x800100020701ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

Alert Category

Warning - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0476

User Response

Replace the system battery.

•

80010202-0701ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

asserted. (CMOS Battery)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102020701ffff or 0x800102020701ffff

Severity

Error

Serviceable

Appendix A. Integrated management module II (IMM2) error messages

443

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands