Lenovo x3650 M5 Installation And Service Manual Download Page 518

Page: 518 / 1340

May also be shown as 8007021b0302ffff or 0x8007021b0302ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0522

User Response

1. Check for a server firmware update.

2. Make sure that the installed microprocessors are compatible.

3. Make sure the microprocessor 2 expansion board is installed correctly (see Installing the

microprocessor 2 expansion board).

4. (Trained technician only) Replace microprocessor 2.

5. (Trained technician only) Replace microprocessor 2 expansion board.

•

80070228-2e01ffff : Sensor [SensorElementName] has transitioned to critical from a less severe

state. (ME Error)

This message is for the use case when an implementation has detected a Sensor transitioned to critical
from less severe.

May also be shown as 800702282e01ffff or 0x800702282e01ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0522

506

Lenovo System x3650 M5 Installation and Service Guide

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands