Lenovo x3650 M5 Installation And Service Manual Download Page 461

Page: 461 / 1340

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat rear hdd cage riser n.

2. Remove the following component and identify the problem. a. HDD drive b. HDD cable c.

RAID card d. cage riser n

3. Replace rear hdd cage riser n (n = riser number).

•

80010204-1d09ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

asserted. (Fan Riser2A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d09ffff or 0x800102041d09ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat rear hdd cage riser n.

2. Remove the following component and identify the problem. a. HDD drive b. HDD cable c.

RAID card d. cage riser n

3. Replace rear hdd cage riser n (n = riser number).

•

80010204-1d0affff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

asserted. (Fan Riser2B Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d0affff or 0x800102041d0affff

Appendix A. Integrated management module II (IMM2) error messages

449

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands