Lenovo x3650 M5 Installation And Service Manual Download Page 767

Page: 767 / 1340

CIM Information

Prefix:

PLAT

ID:

0126

User Response

Make sure that DIMMs are installed in the correct sequence and have the same size, type, speed,
and technology.

•

806f070c-2002ffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 2)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c2002ffff or 0x806f070c2002ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0126

User Response

Make sure that DIMMs are installed in the correct sequence and have the same size, type, speed,
and technology.

•

806f070c-2003ffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 3)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c2003ffff or 0x806f070c2003ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Memory

Appendix A. Integrated management module II (IMM2) error messages

755

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands