Lenovo x3650 M5 Installation And Service Manual Download Page 1150 | Manualshive

Page: 1150 / 1340

background image

Severity

Error

User Response

Complete the following steps:

1. This event resets UEFI to the default settings for the next boot. If successful, the Setup Utility is

displayed. The original UEFI settings are still present.

2. If you did not intentionally trigger the reboots, check logs for probable cause.

3. Undo recent system changes (settings or devices added). If there were no recent system

changes, remove all options, and then remove the CMOS battery for 30 seconds to clear CMOS
contents. Verify that the system boots. Then, re-install the options one at a time to locate the
problem.

4. Check the Lenovo support site for an applicable service bulletin or firmware update that

applies to this error.

5.

Update the UEFI firmware.

6. Remove and re-install CMOS battery for 30 seconds to clear CMOS contents.

7. (Trained service technician only) Replace the system board.

•

S.3060007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to

this error.

2.

Update the UEFI image.

3.

Replace the system board.

•

S.3070007 A firmware fault has been detected in the UEFI image. Internal UEFI Firmware Fault

Detected, System halted

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to

this error.

2.

Update the UEFI image.

3.

Replace the system board.

1138

Lenovo System x3650 M5 Installation and Service Guide

«
...
1148
1149
1150
1151
1152
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

SuperServer E100-8Q

Brand: Supermicro Pages: 48

BladeCenter HS23

Brand: IBM Pages: 28

NEC Express5800 Series

Brand: NEC Pages: 4

NEC Express5800 Series

Brand: NEC Pages: 21

NEC Express5800 Series

Brand: NEC Pages: 10

NEC Express5800 Series

Brand: NEC Pages: 22

NEC Express5800 Series

Brand: NEC Pages: 71

NEC Express5800 Series

Brand: NEC Pages: 166

NEC Express5800 Series

Brand: NEC Pages: 16

Brand: Vicon Pages: 2

Brand: MSI Pages: 107

Vlinx Serial Servers ESP901E

Brand: B&B Electronics Pages: 92

FusionServer G5500 V6

Brand: xFusion Digital Technologies Pages: 100

Netfinity 4500R

Brand: IBM Pages: 60

AcquiLite A7810

Brand: Obvius Pages: 29

Brand: Viavi Pages: 11

Brand: Meinberg Pages: 4

Brand: Inspur Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands