Lenovo x3650 M5 Installation And Service Manual Download Page 407

Page: 407 / 1340

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0114

User Response

Information only; no action is required.

•

40000073-00000000 : The maximum power cap value changed from [arg1] watts to [arg2] watts.

Maximum Power Cap value changed

May also be shown as 4000007300000000 or 0x4000007300000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0115

User Response

Information only; no action is required.

•

40000074-00000000 : The soft minimum power cap value changed from [arg1] watts to [arg2] watts.

Soft Minimum Power Cap value changed

May also be shown as 4000007400000000 or 0x4000007400000000

Severity

Info

Appendix A. Integrated management module II (IMM2) error messages

395

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands