Lenovo x3650 M5 Installation And Service Manual Download Page 282

Page: 282 / 1340

Media cage

Media cage bezel

Figure 232. Retention bracket installation

12. Install the media cage (see “Replacing the media cage (also called lightpath LCD operation panel

assembly)” on page 184).

13. Replace the top cover (see “Replacing the top cover” on page 151).

14. Slide the server into the rack.

15. Reconnect the power cords and any cables that you removed.

16. Turn on the peripheral devices and the server.

Removing the operator information panel assembly

Use this information to remove the operator information panel assembly.

To remove the operator information panel, complete the following steps.

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 297.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Remove the top cover (see “Removing the top cover” on page 149).

Step 4.

Disconnect the cable from the back of the operator information panel assembly.

Step 5.

Pull up the release tab slightly and

slide the operator information panel assembly out of

the server.

270

Lenovo System x3650 M5 Installation and Service Guide

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands