background image

 

12-10 Shortcuts

 

Shortcuts

 

Loading Paper 

 

(p. 14-2)

 

Main Body User-Adjustable Trays: Tray 1 (500), Tray 2 (500), and Tray 3 (1,500)

 

1 Withdraw the main body tray, then place paper into the tray with the curl turning up.

Load size 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R or 5.5"x8.5" (crosswise).
Do not stack paper above the level of the red line.

2 Move the green levers located at the front and left side until they meet the edge of the 

stack of paper.

3 When paper is seated properly, push the tray back fully into the copier.

 

LCC (Large Capacity Cassette: 9930/9932) Service-Adjustable Tray 4 (4,000)

 

1 Open the LCC top door (lift lid).
2 Press the Paper loading button located at the front of the LCC to lower the bottom 

plate of the LCC.

3 Load the fixed size paper into the LCC with the paper curl turning down (see note).
4 Repeat Steps 2 and 3 until the bottom plate cannot go down any more.

Do not stack paper above the paper hook level.

5 When the stack of paper is seated properly in the tray, close the LCC top door (lid).

 

NOTE: When loading tabbed sheets, be sure the tab extensions are positioned at the rear side of the tray (not at 

the front where the Paper load button is located), and jutting to the right, away from the hinged side of the 
LCC cover.

 

Adding Toner 

 

(p. 14-7)

 

CAUTION

 

Keep toner cartridge away from children. Although the toner is non-toxic, do not inhale it or allow it to 
enter your eyes. In case the toner comes in contact with eyes, please consult your physician.

 

1 Open the toner access door and pull the toner cartridge holder lever forward.
2 Withdraw the toner cartridge holder, then remove the empty toner cartridge.
3 Shake the new toner cartridge several times to loosen toner, then remove the 

cartridge cap.

4 Set the new toner cartridge into the toner cartridge holder, aligning the rear part of the 

cartridge with the toner cartridge holder.

5 Push the toner cartridge holder lever backward, then return the toner cartridge holder 

to its original position.

6 Close the toner access door.

 

NOTE: Use the toner cartridge of the same number as the number described on the label of a toner access door 

inner side, otherwise the machine trouble may occur.

DL650us12v1.fm 10 ページ 2001年11月14日 水曜日 午後3時32分

Summary of Contents for DL650

























































































































































































































































































































































Reviews: