manualshive.com logo in svg

Huawei Quidway NetEngine40E, Configuration Manual - Reliability

Share
Download
Huawei Quidway NetEngine40E Configuration Manual - Reliability Download Page 241

l

Configuration file of CE3

#
 sysname CE3
#
interface GigabitEthernet1/0/0
 undo shutdown
 ip address 172.18.1.1 255.255.255.0
#
ospf 100
 area 0.0.0.0
  network 172.18.1.0 0.0.0.255
#
return

l

Configuration file of CE4

#
 sysname CE4
#
interface GigabitEthernet1/0/0
 undo shutdown
 ip address 172.19.1.1 255.255.255.0
#
ospf 200
 area 0.0.0.0
  network 172.19.1.0 0.0.0.255
#
return

4.12.4 Example for Configuring a VRRP Backup Group on VLANIF
Interfaces

In this example, user packets are sent to a UPE that is dual-homed to two directly connected
NPEs. The three devices form a ring network. A VRRP backup group is configured on VLANIF
interfaces of these NPEs to implement device backup. Broadcasting VRRP packets on the ring
network causes broadcast storms. A ring network protocol needs to be configured to prevent this
problem. In this example, the Multiple Spanning Tree Protocol (MSTP) is used.

Networking Requirements

NOTE

POS interfaces cannot be configured on the X1 and X2 models of the NE80E/40E.

On the network shown in 

Figure 4-20

, a UPE is dual-homed to two directly connected NPEs,

forming a ring network. VRRP backup group 1 is configured on VLANIF 10 of NPE1.

NPE1 is the master device and periodically broadcasts VRRP packets through VLAN 10's
member interfaces to inform NPE2 that NPE1 is working properly. VLAN 10's member
interfaces include GE1/0/1 and Eth-Trunk1 members GE 2/0/0 and GE 2/0/1. The deployment
causes broadcast storms on the ring network.

A ring network protocol can be configured to break loops and prevent broadcast storms.

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability

4 VRRP Configuration

Issue 02 (2014-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

224

Summary of Contents for Quidway NetEngine40E

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands