HP XP20000/XP24000 Manual Download Page 325

Page: 325 / 448

Table 56 Error Codes — Part Code 6510

(continued)

Failure
Level

Severity
Level

Recommended Action

Error Message

Error
Number

Part
Code

Specify normal deletion, or
specify Group as the range.

You want to forcibly delete
pairs, but there are some
pairs where Group is not
specified as the range.

Specify Group as the range
when you want to forcibly
delete pairs.

55229

6510

To delete pairs, click [Yes].
Otherwise, click [No].

[Warning]

There are some pairs where
Group is not specified as the
range in the pairs specified
to be deleted forcibly.

Other pairs in the same
group may suspend due to a
failure by this operation.

Are you sure you want to
delete pairs?

55644

6510

There is no journal group that
can be used as a master
journal group.

56504

6510

There are no secondary
subsystems available.
Register secondary
subsystems and then retry the
operation.

56505

6510

There are no consistency
groups available. Create
unused consistency groups,
and then retry the operation.

There are no consistency
groups available. Create
unused consistency groups
and then retry the operation.

56522

6510

Check the mirrors of the
specified volume.

No more mirrors can be
created for the specified
volume.

56523

6510

Check the error information.

An error occurred. Check the
error details.

59004

6510

Specify the valid value.

An invalid value is specified.

59005

6510

Check the number of journal
volumes in the specified
journal group, or check the
number of the selected
volumes.

No more journal volumes can
be registered, or too many
volumes are selected.

59006

6510

To delete the specified
storage system, click [OK].
Otherwise, click [Cancel].

Are you sure you want to
delete the specified
subsystems?

59007

6510

To delete the specified path,
click [OK]. Otherwise, click
[Cancel].

Are you sure you want to
delete the paths of the
specified subsystem?

59008

6510

Click [OK]. Apply the
Preview data to the disk
storage system, and then
retry the operation.

Since the number of Preview
data exceeded the maximum,
the excess data were
discarded. No more Preview
data can be stored.

59009

6510

Remote Web Console Error Codes 325

Summary of Contents for XP20000/XP24000

































































































































































































































































































































































































































































Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands

HP XP20000/XP24000, Manual

Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands