HP XP20000/XP24000 Manual Download Page 72

Page: 72 / 448

Table 16 Error Codes — Part Code 0405

(continued)

Failure
Level

Severity
Level

Recommended Action

Error Message

Error
Number

Part
Code

Isolate the abnormal section
following the procedure
below:

Rebooting the computer.
If this does not fix the
problem:

Checking the LAN
card/LAN cable. If this
does not fix the problem:

Checking the IP address
of the computer. If this
does not fix the problem:

Replacing the computer.
If a new computer does
not fix the problem:

Turn the DKC on, and then
off (care should be taken.)

The subsystem status is
invalid. Call HP technical
support.

8003

0405

Contact HP technical support
for the plans of the program
product to be supported by
DKCMAIN.

The DKCMAIN microcode
does not support this program
product.

8202

0405

Call HP technical support.

This program product needs
a later version of hardware.
Call HP technical support.

8203

0405

Install additional shared
memory and enable the
program product.

To use the program product,
it needs to be enabled by
installing additional shared
memory.

8204

0405

Call HP technical support.

This program product remains
in the configuration. Call HP
technical support.

8205

0405

Stop using this program
product function.

This program product is in
use, you cannot uninstall this
program.

8206

0405

Retry this operation.

The subsystem status is
invalid. Call HP technical
support.

8301

0405

Delete the allocated license
from the SLPR, and then
uninstall the program
product.

The specified program
product cannot be
uninstalled, because the
license for it is allocated to
the SLPR.

55263

0405

Check the licensed capacity
of SLPR0.

Since the licensed capacity
of SLPR0 is insufficient, the
partition capacity can't be
increased.

55506

0405

If this problem persists, call
HP technical support.

It is not possible to install it
because of PP of pre-install.

55520

0405

Install the program product
by using another license key
code.

A license key code which
had been already deleted
was installed.

56508

0405

Remote Web Console for Storage System Messages and Error Codes

Summary of Contents for XP20000/XP24000

































































































































































































































































































































































































































































Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands

HP XP20000/XP24000, Manual

Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands