HP XP20000/XP24000 Manual Download Page 410

Page: 410 / 448

Table 67 Error Codes — Part Code 8105

(continued)

Failure
Level

Severity
Level

Recommended Action

Error Message

Error
Number

Part
Code

Correct the WWN.

The same WWN is already
registered.

5757

8105

Correct the group ID.

No name can be added to
the group ID (00).

5758

8105

Correct the name.

The same name is already
registered.

5759

8105

Correct the WWN.

The WWN does not exist.

5761

8105

Correct the name.

The name does not exist.

5762

8105

Add the LUN to another
group or another port.

The number of LUN cannot
exceed 512 per port or 256
per host group.

5764

8105

Correct the LUN.

The LUN is already used.

5765

8105

Correct the CU and LDEV.

The specified CU:LDEV is
invalid.

5766

8105

Correct the LUN.

The LUN does not exist.

5767

8105

Correct the LUN.

There is a difference between
the current LUN and the
specified LUN.

5768

8105

Correct the group ID.

The group cannot be added.

5769

8105

Set the port attribute to target
in advance.

The port cannot be changed
because the port is an
initiator port.

5770

8105

The PCB mode value is
invalid. Specify a correct
value.

The setting cannot be
performed, because an
invalid PCB mode is set to the
specified CHA.

5771

8105

Correct the CU and LDEV.

The system LU cannot be
used.

5785

8105

Correct the name of port.

The path can be defined only
for the A, E, J or N port.

5786

8105

Correct the CU and LDEV.

The intermediate volume
cannot be specified as a
command device.

5789

8105

If nothing changes despite
retrying, call HP technical
support.

A program error occurred
under internal process.

5790

8105

If this problem persists, call
HP technical support.

An error occurred during SVP
processing. If this problem
persists, call HP technical
support.

6012

8105

If the same problem persists
despite retrying, call HP
technical support.

The SVP is busy. Please wait
for a while, and then retry the
operation.

6023

8105

Retry the operation a little
later.

A command was double
started.

6513

8105

410

Remote Web Console for Storage System Messages and Error Codes

Summary of Contents for XP20000/XP24000

































































































































































































































































































































































































































































Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands

HP XP20000/XP24000, Manual

Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands