HP XP20000/XP24000 Manual Download Page 429

Page: 429 / 448

Table 82 Error Codes — Part Code 9105

(continued)

Failure
Level

Severity
Level

Recommended Action

Error Message

Error
Number

Part
Code

If this problem persists, call
HP technical support.

An error occurred during SVP
processing. If this problem
persists call HP technical
support.

7060

9105

An error occurred during SVP
processing. If this problem
persists, call HP technical
support.

7111

9105

If this problem persists, call
HP technical support.

Unregistered error code.

7310

9105

Retry the operation. If you get
the same message again,
reboot the computer. If
necessary, call HP technical
support.

A communication time-out
error occurred.

8001

9105

Wait a moment and retry.

Communication is busy. Retry
later.

8002

9105

Call HP technical support.

The SVP version and the DKC
version do not match.

8102

9105

Call HP technical support.

The configuration could not
be changed.

8110

9105

Install PCBs for mainframe
computers, and then retry the
operation.

No PCBs are installed for
mainframe computers.

8659

9105

Release the journal volume
setting, or delete the target
volume from the LDEV group.

The specified LDEV is a
journal volume, and therefore
cannot be registered in LDEV
groups.

55548

9105

Select another window. To
set this function, contact the
storage administrator.

This function cannot be used
by the storage partition
administrator.

56524

9105

If this problem persists, call
HP technical support.

The LDKC Number is
incorrect.

67000

9105

There are no volumes
mounted. Install additional
volumes to execute the
operation.

There are no LDKCs mounted.

67001

9105

Specify another security
group name.

The specified security group
name has already been used
by another LDKC.

67002

9105

Specify another host group
name.

The specified host group
name has already been used
by another LDKC.

67003

9105

Specify other LDEV group
name.

The specified LDEV Group
name has already been used
by another LDKC.

67004

9105

Remote Web Console Error Codes 429

Summary of Contents for XP20000/XP24000

































































































































































































































































































































































































































































Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands

HP XP20000/XP24000, Manual

Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands