HP XP20000/XP24000 Manual Download Page 117

Page: 117 / 448

Table 26 Error Codes — Part Code 1005

(continued)

Failure
Level

Severity
Level

Recommended Action

Error Message

Error
Number

Part
Code

Associate the XP Thin
Provisioning volume with the
same pool, and then retry the
operation.

The XP Thin Provisioning
volume is not associated with
a pool. Associate the XP Thin
Provisioning and a pool first.

65660

1005

Select another volume.

XP Thin Provisioning
volume(s) cannot be
combined into LUSE volumes.

65672

1005

Associate the XP Thin
Provisioning volumes with the
same pool, and then retry the
operation.

The Thin Provisioning volumes
are not associated with the
same pool. Associate the XP
Thin Provisioning volumes
with the same pool first.

65704

1005

Table 27 Error Codes — Part Code 1010

Failure
Level

Severity
Level

Recommended Action

Error Message

Error
Number

Part
Code

Correct the specified content,
and issue the request again.
(Currently, Bad Value Send
report in Set Response.)

The specified fibre address is
invalid.

1023

1010

Correct the specified
contents, and request the
setting of the configuration
information again.

The specified host group is
already used.

1065

1010

Correct the specified content,
and retry.

The specified LDEVs and free
LUNs should be the same
number.

5010

1010

You cannot specify any more.

The number of LU paths in
use has already reached the
maximum (2,048 in a Fibre
Channel environment).

5040

1010

Reduce the number, and
retry.

The number of LUNs in use
has already reached the
maximum number of LUNs
that can be specified per host
group (2,048 in a Fibre
Channel environment).

5041

1010

Reduce the number, and
retry.

The number of LUNs in use
has already reached the
maximum number of LUNs
that can be specified per port
(2,048 in a Fibre Channel
environment).

5042

1010

Reduce the number, and
retry.

The selected number of LDEVs
exceeds the number of free
LUNs.

5043

1010

Check the content of the
operation.

The specified LUN had been
set.

5050

1010

Check the content of the
operation.

The selected LUN is not a
command device.

5051

1010

Check the content of the
operation.

Select the LUN that is already
assigned.

5052

1010

Remote Web Console Error Codes

117

Summary of Contents for XP20000/XP24000

































































































































































































































































































































































































































































Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands

HP XP20000/XP24000, Manual

Search results

Summary of Contents for XP20000/XP24000

Reviews:

Related manuals for XP20000/XP24000

Brands by name

Popular brands