Hi-Target Surveying Instrument ZTS-360R Manual Download Page 1

Page: 1 / 143

Hi-Target Surveying Instrument Co. Ltd.

NAME: TOTALSTATION

MODEL:ZTS-360R

The statements should be displayed in the user manual:

changes or modifications not expressly approved by the

party responsible for compliance could void the user

’

s authority

to operate the equipment.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications.However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and

receiver.

-- Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician

for help.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands