GAL GALaxy eHydro Manual Download Page 145

Page: 145 / 248

GALaxy eHydro Elevator Controller Section 6

– Main CPU Faults & Detailed Faults

6-81

Table 6-0: Main CPU Faults

Faults

Description

Possible Cause/Suggested Fix

SUF I/O
Failed On

The SUF input or
output has failed on.

• Faulty SUFi input. Swap input board to see if SUFi input

chip is bad and replace input board if necessary.

• The SUF test jumper was left on the output

after an I/O

test. Remove test jumper.

• Voltage back feed through the SUF coil. Verify that the SUF

solenoid is connected to the solenoid common. Refer to the
schematic and check the circuit with a meter.

• Faulty SUF output. Swap the output with another

device to

verify if the output is bad and replace if necessary.

SUF I/O On
Fault

SUF I/O Failed on
when stopped at the
floor.

After the car stops at the floor and the RUN output drops,
the SUF and SDF I/Os are check to verify that they have
turned off.

• Verify that the LED on the output module has turned off.

If not then replace the output module.

• Check for voltage on the solenoid terminal. If there is no

voltage then replace the appropriate input board.

• If there is voltage on the solenoid te

rminal, remove the

output module. If the voltage goes away with the removal of
the output module, replace the output module.

Top Door Lock Fault

The Top Door Lock
failed on while the
door was open.

• Faulty door lock.

• Jumper on door lock circuit.

• Doo

r lock not adjusted properly.

• Faulty wiring to DLT input.

• Faulty DLT and DLT

-1 inputs (For this to occur both DLT

and DLT-1 inputs must fail on).

• DOL input failed. Replace DOL input chip.

• Door operator open limit DOL is not adjusted properly

Trace Trigger

The Data Trace has
been triggered. This is
not a fault

UL and DL Off Fault

Both UL and DL level
inputs are off when
car is at a floor. These
two inputs are set
from counts from the
APS selector.

• Verify that the Main CPU is

communicating with the APS

selector.

• Verify that the Main CPU has a valid floor table.

Summary of Contents for GALaxy eHydro

























































































































































































































































Search results

Summary of Contents for GALaxy eHydro

Reviews:

Related manuals for GALaxy eHydro

Brands by name

Popular brands

GAL GALaxy eHydro, Manual

Search results

Summary of Contents for GALaxy eHydro

Reviews:

Related manuals for GALaxy eHydro

Brands by name

Popular brands