GAL GALaxy eHydro Manual Download Page 146 | Manualshive

Page: 146 / 248

background image

GALaxy eHydro Elevator Controller Section 6

– Main CPU Faults & Detailed Faults

6-82

Table 6-0: Main CPU Faults

Faults

Description

Possible Cause/Suggested Fix

UL DL Dist Too Large

The UL and DL
distance settings are
the number of counts
the car runs after the
UL and DL dead level
inputs are active. If
the UL or DL distance
is set greater than 2
inches, the controller
will get this error
when it attempts to
verify the hoistway
table.

• The UL and DL distances are set in the Hoistway Tables

menu on the LCD display interface. Select the UL & DL
Distance menu and then set the UL or DL distance to the
proper value.

UL Failed On Fault

UL Failed On Fault.
The UL input did not
go off during a run.
The UL input is set
from a count from the
APS selector.

• The APS selector did not change count during a run. Check

for faults related to the APS selector. Verify that the APS
selector counts change while the car is running.

• The elevator did not leave the floor on a run attempt.

Verify that the elevator can run from the landing. Check the
fault log for another fault that could prevent the car from
running.

UL, DL & DZ
Off at FL

UL, DL & DZ inputs off
at floor. The car thinks
it should be at a floor
or is at a floor and all
the floor inputs have
turned off.

• Verify that the Main CPU is communicating with the APS

selector.

• Verify that the Main CPU has a valid floor table.

Up Directional Fault

Car unexpectedly hit
the Up Normal Limit
while running up.

• The Safety PAL detected a fault condition and turned off

the UN output from the NTS processor.

• The NTS proce

ssor detected a fault condition and turned

off the UN output.

• APS Selector communications loss to the Main CPU.

• APS Selector communications loss to the NTS processor.

• Selector not reading the correct position from the tape.

User Variable Init

User variable
initialization

User related parameters such a password and telephone
numbers are being initialized. This error occurs on the first
time the GALX-1132 CPU board is being powered up.

«
...
144
145
146
147
148
...
»

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

Brand: GBD Pages: 68

Brand: Fanimation Pages: 2

Brand: M2M Pages: 24

Brand: Patron Pages: 17

FT-2000 - MENU MODE LIST

Brand: Yaesu Pages: 56

Q Module WFZ16.Ox

Brand: QUNDIS Pages: 24

Brand: Game ready Pages: 24

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Baier Pages: 20

Brand: ECKELMANN Pages: 147

Brand: Squizz Pages: 24

Brand: Quantum Pages: 20

Brand: AC Tech Pages: 2

Brand: V-TAC Pages: 2

Brand: Diamond Systems Pages: 15

Brand: Carel Pages: 2

Brand: Kelly Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands