GAL GALaxy eHydro Manual Download Page 141

Page: 141 / 248

GALaxy eHydro Elevator Controller Section 6

– Main CPU Faults & Detailed Faults

6-77

Table 6-0: Main CPU Faults

Faults

Description

Possible Cause/Suggested Fix

RUN I/O
Failed On

The RUN input or
output has failed on.

• The RUN relay has failed on or RUN relay contact has

failed in the closed position. Replace the RUN relay.

• Faulty RUNi input. Replace the RUNi input chip.

• Faulty RUN output. Replace the RUN output chip.

• The solenoid

common is shorted to GND. Refer to the

schematic and check the circuit with a meter.

Run Inhibit Rset Cnt

Run inhibit from reset
count

• Once the car is in Reset mode, the controller attempted 5

times to come off reset but it keeps being sent back to the
reset mode because of a fault condition.

S10 Fuse Blown Fault

The S10 input is off.
No Power on S10

• Short from S10 to GND.

Safety String Fault

Safety string fault
occurs from the
following conditions:

•

The safety string is
open from one of the
following inputs being
off: GOV, HSS, EXT,
CSS, CTS, FFS, CST,
MRSW.

• The safety string is open (One or more of the safety inputs

are off). Refer to the job prints and check all circuits ahead
of the MRSW input.

SD I/O Failed Off

The SD input or
output has failed off.

• Faulty SDi input. Swap input board to see if SDi input chip

is bad and replace input board if necessary.

• The SD solenoid is shorted to GND at the SD terminal.

Refer to the schematic and check the circuit with a meter.

• Faulty

SD output. Swap the output with another device to

verify if the output is bad and replace if necessary.

SD I/O Failed On

The SD input or
output has failed on.

• Faulty SDi input. Swap input board to see if SDi input chip

is bad and replace input board if necessary.

• The SD test jumper was left on the output after an I/O

test. Remove test jumper.

• Voltage back feed through the SD coil. Verify that the SD

solenoid is connected to the solenoid common. Refer to the
schematic and check the circuit with a meter.

• Faulty SD output. Swap the output with another device to

verify if the output is bad and replace if necessary.

Summary of Contents for GALaxy eHydro

























































































































































































































































Search results

Summary of Contents for GALaxy eHydro

Reviews:

Related manuals for GALaxy eHydro

Brands by name

Popular brands

GAL GALaxy eHydro, Manual

Search results

Summary of Contents for GALaxy eHydro

Reviews:

Related manuals for GALaxy eHydro

Brands by name

Popular brands