GAL GALaxy eHydro Manual Download Page 133 | Manualshive

Page: 133 / 248

background image

GALaxy eHydro Elevator Controller Section 6

– Main CPU Faults & Detailed Faults

6-69

Table 6-0: Main CPU Faults

Faults

Description

Possible Cause/Suggested Fix

MRCan Bus Off Error

MRCan Bus Off Error.
The Can bus has been
inactive for too long a
period of time.

• Faulty CAN bus wiring. Check the Can bus

terminal

connections on all boards.

MRCAN
Device Fault

Device on the
Machine Room CAN
Port has a Fault. On
the LCD Interface, this
fault is display as an
abbreviated device
name and device fault.
Please see the device
faults for further
information.

• Look at the details of the fault. The device name and the

error code that caused the fault are listed.

• Look up the fault code for the device for debugging

information.

MRCAN
Device Reset

Device on the
Machine Room CAN
Port has reset. On the
LCD Interface, this
fault is display as an
abbreviated device
name and device fault.
Please see the device
faults for further
information.

• Look at the details of the fault. The device name and the

error code that caused the fault are listed.

• The device requested an initialization packet from the

main CPU. Typically, this occurs during power up or from a
power cycle of the individual device.

• Ignore the error if the controller power has been cycled.

Otherwise, check the device
communications and power connections.

NTS DN
Failed Off

NTS DN I/O Failed Off
during start or
leveling. The
controller is
attempting to run the
car in the down
direction but the UN
input is off.

• The DN output failed. Replace the DN output module.

• The DN input

failed. Replace the DN input board.

• The NTS processor has turned the DN output off. Check

for errors from the NTS processor.

• The NTS processor has a position error from the APS

selector. Verify the setup of the APS selector and that the
NTS processor is communicating with the selector.

• The Safety PAL has determined that it is unsafe to run the

car such as the doors are
open. Check for a Safety Pal Fault and check the status of
the I/Os of the Safety PAL.

«
...
131
132
133
134
135
...
»

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

Brand: Zetkama Pages: 6

Brand: Facility Explorer Pages: 4

Brand: Eaton Pages: 100

Brand: Haldex Pages: 8

Brand: tams elektronik Pages: 12

Brand: L-Acoustics Pages: 20

Brand: Eaton Pages: 96

Brand: WAGNER Pages: 60

Brand: Vag Pages: 15

DuetPro Carrycot

Brand: Qtus Pages: 52

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Penn Pages: 10

Brand: Zander Aachen Pages: 75

Brand: Chamberlain Pages: 4

Brand: Shimaden Pages: 16

SUPERSEAL 2014 Series

Brand: APV Pages: 20

Brand: LEYBOLD Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands