manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                     Section 6 

– Main CPU Faults & Detailed Faults

 

6-85 

 

 
 

Table 6-1: Device Faults from the CTCAN, GRCAN and MRCAN Serial Ports 

Fault 

Description 

Possible Cause/Suggested Fix 

APS Com 
Fault 

NTS Processor has a 
communications 
fault with the APS 
selector head. 

 

• Faulty communications from the NTS CAN terminals on the 1121 MAIN 

I/O board to the NTS CAN terminals on the 1134 COP board. Make sure 
the CANH and CANL wires match. 

• Termination resistors are usually place at the far end of each 

BUS.  

Verify the placement of the Termination resistors. 

• Check the RJ

-45 connection from the 1134 COP board to the APS 

selector camera. 

• Try moving the termination resistors to other locations.

 

• Faulty device, try replacing each board individually, the

 1121 Main I/O 

board, the 1134 
COP board and APS selector camera. 

Comm 
Fault 

Device has a 
communications 
fault. 

 

• Faulty communications wiring to the device.

 

• Termination resistors are usually place at the far end of each BUS.  

Verify the placement of the Termination resistors. 

• Try moving the termination resistors to other locations.

 

• Faulty device, replace board.

 

DZ Clip 
Fault 

 
The NTS processor 
has a DZ clip fault.  
The NTS processor 
keep track of when 
the door zone clip is 
read at each floor.  If 
it enters a floor and 
the clip is not read at 
that floor three 
times in a row, this 
fault is logged. 

• Check the placement of the clip when the car is dead level to the floor. 

The clip should be in between the two channels of APS cameras. 
Momentarily place your hand in front of the camera to cause the red LED 
markers to turn on.  The clip should be roughly in the middle of the red 
LED markers. 

• Verify that the clip is not broken or that the

 

correct clip is installed. Replace or install the correct clip. 

HW Fl 
Cnt Inv 

Hoistway Floor 
Count is Invalid on 
the NTS processor. 
One or more floor 
count of an above 
floor is less than the 
floor below. 

 

• The hoistway floor table is not setup properly. Check the valid floor 

table of the NTS processor on the LCD Interface in the Hoistway Table 
Valid Floor and Clips menu.  Run car to the  floor with the position of the 
invalid floor or floors and learn the floor position. 

• Complete the setup process.

 

• Faulty NTS processor. Replace the 1121 Ma

in I/O board.  Contact Tech 

Support. 

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

Rain Bird IQ Installation & User Manual preview
IQ
Brand: Rain Bird Pages: 48
ABC Design Tandem Instructions For Use Manual preview
Tandem
Brand: ABC Design Pages: 38
easydriver Pro Installation And Instruction Manual preview
Pro
Brand: easydriver Pages: 26
Calsense CS3000 Quick Start Manual preview
CS3000
Brand: Calsense Pages: 10
ABC Design Rodeo Instructions Manual preview
Rodeo
Brand: ABC Design Pages: 10
ABC Design Astro Instruction Manual preview
Astro
Brand: ABC Design Pages: 10
Hach sc200 Software Update preview
sc200
Brand: Hach Pages: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Brand: Hach Pages: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Brand: Hach Pages: 472
Hach sc1000 User Manual preview
sc1000
Brand: Hach Pages: 64
V2 ELETTRONICA CL1 Quick Start Manual preview
CL1
Brand: V2 ELETTRONICA Pages: 6
Hach SC4500 Basic User Manual preview
SC4500
Brand: Hach Pages: 210
jablotron Oasis JA-80 Installation Manual preview
Oasis JA-80
Brand: jablotron Pages: 22
jablotron JA-113E Manual preview
JA-113E
Brand: jablotron Pages: 2
Omega PHCN-37 User Manual preview
PHCN-37
Brand: Omega Pages: 56
Omega DP25-TC Quick Start Manuals preview
DP25-TC
Brand: Omega Pages: 2
Panamax M4000-PRO Instructions Manual preview
M4000-PRO
Brand: Panamax Pages: 16
Ultratec SureFire Operation Manual preview
SureFire
Brand: Ultratec Pages: 33

Brands by name

Popular brands

Load more brands