manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                     Section 6 

– Main CPU Faults & Detailed Faults

 

6-71 

 

Table 6-0: Main CPU Faults 

Faults 

Description 

Possible Cause/Suggested Fix 

NTS UNFailed Off 

NTS UN I/O Failed Off 
during start or 
leveling. The 
controller is 
attempting to run the 
car in the up direction 
but the UN input is 
off. 

• The UN output failed.  

Replace the UN output module.

• 

The UN input failed.  Replace the UN input board.

• The NTS 

processor has turned the UN output off.  Check for errors 
from the NTS processor.

• The NTS processor has a position 

error from the APS selector.  Verify the setup of the APS 
selector and that the NTS processor is communicating with 
the selector.

• The Safety PAL has determined that it is 

unsafe to run the car such as the doors are open.  Check for 
a Safety Pal Fault and checkthe status of the I/Os of the 
Safety PAL. 

NTS UN 
Failed On 

 
NTS UN I/O Failed On 
during start. As part of 
the redundancy check, 
the Main CPU sends a 
command to the NTS 
processor to turn of 
the UN, DN, UT and 
DT outputs prior to 
turning on any valve 
outputs to verify that 
the NTS outputs have 
not faulted on. During 
this process, the UN 
output or the UN 
input stayed on. 

• UN output shorted on.  Replace the output module.

 

• UN input failed on.  Replace the input board.

 

• UN test jumper left on the module.  Remove the test 

jumper. 

NTS UT 
Failed Off 

NTS UT I/O Failed Off 
during start. The 
controller is 
attempting to run the 
car high speed in the 
up direction but the 
UT input is off. 

 

• The UT output failed.  Replace the UT output module.

 

• The NTS processor has turned the UT output off.  Ch

eck 

for errors from the NTS processor. 

• The NTS processor has a position error from the APS 

selector.  Verify the setup of the APS selector and that the 
NTS processor is communicating with the selector. 

• The Safety PAL has determined that it is unsafe to

 run the 

car such as the doors are open.  Check for a Safety Pal Fault 
and check 
the status of the I/Os of the Safety PAL. 

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

ABB LME620-AI Service Instruction preview
LME620-AI
Brand: ABB Pages: 30
ABB LME620-AI Instructions Manual preview
LME620-AI
Brand: ABB Pages: 15
ABB PST30 Manual preview
PST30
Brand: ABB Pages: 10
ABB LME620-AI User Manual preview
LME620-AI
Brand: ABB Pages: 44
NEJE E80 Manual preview
E80
Brand: NEJE Pages: 17
Oceanic ZX Service Procedure preview
ZX
Brand: Oceanic Pages: 13
K&K M8700 Installation Instructions Manual preview
M8700
Brand: K&K Pages: 6
Zeta Premier MX-16 Installation And Commissioning Manual preview
Premier MX-16
Brand: Zeta Pages: 44
+GF+ EA15 Instruction Manual preview
EA15
Brand: +GF+ Pages: 3
Össur ICELOCK 551 Instructions For Use Manual preview
ICELOCK 551
Brand: Össur Pages: 58
Universal Remote Genesis MX-900 Manual preview
Genesis MX-900
Brand: Universal Remote Pages: 20
Jetter 60873050 Manual preview
60873050
Brand: Jetter Pages: 24
Desoutter 6159326760 Original Instructions Manual preview
6159326760
Brand: Desoutter Pages: 74
jablotron CL-301SL Quick Start Manual preview
CL-301SL
Brand: jablotron Pages: 2
KROHNE OPTISWITCH 5100 C Manual preview
OPTISWITCH 5100 C
Brand: KROHNE Pages: 40
ITALCOPPIE SENSORI EVOMINI SCAT A Quick Start Manual preview
EVOMINI SCAT A
Brand: ITALCOPPIE SENSORI Pages: 2
R for Rabbit Poppins Plus Instruction Manual preview
Poppins Plus
Brand: R for Rabbit Pages: 2
Partlow MIC 1161 Operator'S Manual preview
MIC 1161
Brand: Partlow Pages: 49

Brands by name

Popular brands

Load more brands