manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                                          Section 1 

– Product Description 

1-6 

 

1.6   Modes of Operation 

 

1.6.1  Reset Mode  

 

Reset mode is initiated when the elevator power is first turned on, or when the system is reset. When 

the reset mode is initiated, the controller performs internal tests to ensure that both the car and 
controller are electrically operational before putting the car into service. The car will not move until reset 
mode is completed. Some of the internal tests that the controller performs are as follows: is the safety 
string made up; is the elevator on inspection operation; is the door close limit open; are the interlocks 
made up; is hoistway position correct. If all the safeties are made up, and the elevator is on automatic 
operation, and it is at floor level, the elevator will go into automatic mode. If the elevator is not at floor 
level, it will run slow speed down to the nearest floor, level into the floor, and reset the floor position 
count.  

  

1.6.2  Safety String Open Mode  

 

Safety string open mode is initiated when a safety is open. Some of the safeties are listed below:  

  

•

 

Reverse phase relay  

•

 

Governor overspeed switch  

•

 

Top Terminal Limit Switch  

•

 

Pit switch  

•

 

Hatch Safety Switch  

•

 

Exit Door Switch  

•

 

Car Safeties  

•

 

Car top stop switch  

•

 

Fire Fighters Stop Switch  

•

 

In-Car Stop Switch  

•

 

Controller Stop Switch  

  

  

When the safety string is made back up, the elevator will go back to reset mode.  

 

1.6.3  Controller Inspection Mode  

 

The controller inspection mode is initiated by placing the “INS” switch on the 1121 board in the 

inspection position (down). Controller inspection mode permits operation of the car from the machine 
room. This mode performs the following operations:  
  

•

 

Enables the controller inspection “ENABLE”, “UP” and “DOWN” push buttons  

•

 

Door locks are active and must be closed to move the car.  

•

 

Pressing the controller “ENABLE” and “UP” pushbuttons causes the elevator to move at 
inspection speed in the up direction.  

•

 

Pressing the controller “ENABLE” and “DOWN” pushbuttons causes the elevator to move at 
inspection speed in the down direction.  

  

1.6.4  Car Top Inspection Mode  

 

This inspection mode is initiated by placing the inspection switch on top of the car in the inspection 

position. Inspection mode permits operation of the car from the car top inspection station. This mode 
performs the following operations:  

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

Eaton SC300 Operation Handbook preview
SC300
Brand: Eaton Pages: 166
Access Flow2 User'S Manual & Installation Instructions preview
Flow2
Brand: Access Pages: 12
QUAD 34 Instruction Book preview
34
Brand: QUAD Pages: 17
fadini VIGILO 2250 Instruction Manual preview
VIGILO 2250
Brand: fadini Pages: 16
LAS 16261 Quick Manual preview
16261
Brand: LAS Pages: 6
ICP DAS USA XP-9 88-IoT Series Quick Start Manual preview
XP-9 88-IoT Series
Brand: ICP DAS USA Pages: 8
ICON AIRFLOW PCM Manual preview
AIRFLOW PCM
Brand: ICON Pages: 2
ICP DAS USA SP-S2-DS Quick Start preview
SP-S2-DS
Brand: ICP DAS USA Pages: 4
HEIDENHAIN ND 1300 Operating Instructions Manual preview
ND 1300
Brand: HEIDENHAIN Pages: 257
Sutter Instrument TRIO MPC-165 Series Operation Manual preview
TRIO MPC-165 Series
Brand: Sutter Instrument Pages: 60
Sielco Elettronica D1-15A User Manual preview
D1-15A
Brand: Sielco Elettronica Pages: 15
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Brand: Mold-Masters Pages: 2
Spirax Sarco FTC80 Installation And Maintenance Instructions Manual preview
FTC80
Brand: Spirax Sarco Pages: 24
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Brand: Trinamic Pages: 30
Leggett & Platt G-SMR-2 CUSTOM Operation Manual preview
G-SMR-2 CUSTOM
Brand: Leggett & Platt Pages: 20
Bentel KYO 32 M Installation Manual preview
KYO 32 M
Brand: Bentel Pages: 88
Zenith ZH210 Owner'S Manual preview
ZH210
Brand: Zenith Pages: 20
J+J J4C 20 Assembly Instructions Manual preview
J4C 20
Brand: J+J Pages: 6

Brands by name

Popular brands

Load more brands