GAL GALaxy eHydro Manual Download Page 125 | Manualshive

Page: 125 / 248

background image

GALaxy eHydro Elevator Controller Section 6

– Main CPU Faults & Detailed Faults

6-61

Table 6-0: Main CPU Faults

Faults

Description

Possible Cause/Suggested Fix

GRCAN
Device Fault

Device on the Group
CAN Port has a Fault.
On the LCD Interface,
this fault is display as
an abbreviated device
name and device fault.
Please see the device
faults for further
information.

• Look at the details of the fault. The device name and the

error code that caused the fault are listed.

• Look up the fault code for the device for debugging

information.

GRCAN
Device Reset

Device on the Group
CAN Port has reset.
On the LCD Interface,
this fault is display as
an abbreviated device
name and device fault.
Please see the device
faults for further
information.

• Look at the details of the fault. The device name and the

error code that caused the fault are listed.

• The device requested an initialization packet from the

main CPU. Typically, this occurs during power up or from a
power cycle of the individual device.

• Ignore the error if the controller power has been cycled.

Otherwise, check the device communications and power
connections.

Group Comm Loss

The car that was
acting as the group car
has stopped
communicating.

• Faulty

wiring from TX+/TX- from car to car.

• Faulty U6 driver chip on the GALX

-1132 CPU board (next to

the connector for the group comm). Call GAL.

• Noise on shield wire. Connect shield only on one end.

• Noise on the communication wires. Run wires in separate

conduit.

GS & GS_1Opposite

Input failure on one of
the Gate Switch (GS)
inputs.

• GS or GS

-1 input failed on. Replace GS or GS-1 input chip.

•

Check status of input from Input and Output menu on the
LCD interface.

Hall Call Light Fuse

Hall Call Light Fuse
Blown

• Check for short on the Hall Call Light circuit.

Hatch Safety Fault

Hatch Safety Fault.
The HSS input is off.

• A device contact in the hatch safety string has opened.

• The HSS input has failed off.

HC Com Device Reset

Serial Hall Call board
reset unexpectedly.
Usually caused by loss
of power to the
individual board.

• Usually caused by loss of power to the individual board.

• Faulty power connection to board.

• Fault hall call board.

«
...
123
124
125
126
127
...
»

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: Federal Signal Corporation Pages: 34

Brand: ICM Controls Pages: 2

M16/RM N.C. DN 65 EEX

Brand: Madas Pages: 44

Brand: Magellan Pages: 2

PXI-6683 Series

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 29

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 7

FIELDPOINT FP-1600

Brand: National Instruments Pages: 21

FieldPoint FP-1001

Brand: National Instruments Pages: 65

FieldPoint FP-1001

Brand: National Instruments Pages: 19

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 10

Brand: Parker Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands