manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                     Section 6 

– Main CPU Faults & Detailed Faults

 

6-56 

 

Table 6-0: Main CPU Faults 

Faults 

Description 

Possible Cause/Suggested Fix 

EPRecall Car5 Tim-ot 

 
Emergency Power 
Recall Time-out Car 5. 
Car 5 timeout while it 
was in Emergency 
power recall mode. 

 

• Make sure the field variable 'Recall Timeout' is set 

properly to allow the car enough time to recover if it is 
between floors and away from Emergency Power Floor 

• Verify the speed of the car during recovery operation.

 

EPRecall Car6 Tim-ot 

 
Emergency Power 
Recall Time-out Car 6. 
Car 6 timeout while it 
was in Emergency 
power recall mode. 

 

• Make sure the field variable 'Recall Timeout' is set 

properly to allow the car enough time to recover if it is 
between floors and away from Emergency Power Floor 

• Verify the speed of the car during recovery operation.

 

EPRecall Car7 Tim-ot 

 
Emergency Power 
Recall Time-out Car 7. 
Car 7 timeout while it 
was in Emergency 
power recall mode. 

 

• Make sure the field variable 'Recall Timeout' is set 

properly to allow the car enough time to recover if it is 
between floors and away from Emergency Power Floor 

• Verify the speed of the car during recovery operation.

 

EPRecall Car8 Tim-ot 

Emergency Power 
Recall Time-out Car 8. 
Car 8 timeout while it 
was in Emergency 
power recall mode. 

• Make sure the field variable 'Recall Timeout' is set 

properly to allow the car enough time to recover if it is 
between floors and away from Emergency Power Floor

• 

Verify the speed of the car during recovery operation. 

Estop Fault 

An emergency stop 
occurred while moving 
or attempting to 
move.  This fault is 
recorded after three 
emergency stops 
occurred in a row. 

 

• Lost UN while running up at 

contract speed. 

• Lost DN while running down at contract speed.

 

• The MC contactor did not energize or dropped out while 

running 

• The MC input did not turn on or dropped out while 

running. 

• The stop switch was pulled while running.

 

• The car was not safe

 usually from clipping a door lock. See 

Car Safe Fault. 

• Low Pressure Switch activated during the run.

 

• Low Oil Switch activated during the run.

 

• High Temperature sensor activated during the run.

 

• The stall protection timer timed

-out. 

• An emergency po

wer recall was initiated while the car was 

running up. 

FDoor Close Cont Flt 

Door Close Contact 
safe fault 

 

• The car was either running or preparing to run and lost a 

front door close contact input. Check the adjustment of the 
door. 

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

Daikin BRC1E61 Operation Manual preview
BRC1E61
Brand: Daikin Pages: 56
Danfoss ERC 211 User Manual preview
ERC 211
Brand: Danfoss Pages: 36
GSD DCT2RM2501 Quick Start Manual preview
DCT2RM2501
Brand: GSD Pages: 5
Halma ZoneSense Plus AS Manual preview
ZoneSense Plus AS
Brand: Halma Pages: 58
H3C WX1804H Configuration Manual preview
WX1804H
Brand: H3C Pages: 11
Nanjing Putian Datang Information Electronics Co., Ltd. CL12/2410LI-A User Manual preview
CL12/2410LI-A
Brand: Nanjing Putian Datang Information Electronics Co., Ltd. Pages: 2
DUNIWAY Stockroom Terranova 960 Instruction Manual preview
Terranova 960
Brand: DUNIWAY Stockroom Pages: 30
Lutron Electronics Maestro Wireless Pico Series User Manual preview
Maestro Wireless Pico Series
Brand: Lutron Electronics Pages: 6
Wiznet WIZ6000 Manual preview
WIZ6000
Brand: Wiznet Pages: 27
Phoenix Contact FL EPA 2 User Manual preview
FL EPA 2
Brand: Phoenix Contact Pages: 40
HAOZEE NW-HT User Manual preview
NW-HT
Brand: HAOZEE Pages: 16
Weidmüller 1517130000 Manual preview
1517130000
Brand: Weidmüller Pages: 18
Allen-Bradley 1771-OD Installation Data preview
1771-OD
Brand: Allen-Bradley Pages: 8
Pilz PNOZ m EF 4DI4DOR Operating Manual preview
PNOZ m EF 4DI4DOR
Brand: Pilz Pages: 28
tams elektronik KSM-4 Manual preview
KSM-4
Brand: tams elektronik Pages: 20
CAME ZL56A Manual preview
ZL56A
Brand: CAME Pages: 40
Interroll ZoneControl Operating Manual preview
ZoneControl
Brand: Interroll Pages: 54
Uniteck UNISOLAR 20.24 Manual preview
UNISOLAR 20.24
Brand: Uniteck Pages: 46

Brands by name

Popular brands

Load more brands