manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                     Section 6 

– Main CPU Faults & Detailed Faults

 

6-46 

 

Table 6-0: Main CPU Faults 

Faults 

Description 

Possible Cause/Suggested Fix 

CCF Input Failed Off 

 
Contact Confirm Fault 
input failed off. This 
input is used with an 
electronic Bucher 
valve.  The CCF input 
did not turn on during 
start. 

• Faulty CCF input.  Replace the input board.

 

• Faulty Valve Interface.  Please refer to schematic for 

interface circuit. 

CCF Input Failed On 

 
Contact Confirm Fault 
input failed on. This 
input is used with an 
electronic Bucher 
valve.  The CCF input 
did not turn on during 
start. 

• Faulty CCF input.  Replace the input board.

 

• Faulty Valve Interface.  Please refer to schematic for 

interface circuit. 

CFLT Fail Off Fault 

CFLT Input Failed OFF. 
The soft-starter fault 
relay is check once a 
day from the 
controller by cycling 
the STE, Starter 
Enable, output off and 
then on. When STE is 
turned off the CFLT 
input should go on. 
After the CFLT input 
turns on, STE is turned 
back on and CFTL is 
expected to turn back 
off.  If CFLT turns on 
and does not turn 
back on, this fault is 
logged. 

• Faulty soft

-starter fault relay.  Replace the fault relay.

• 

Faulty CFLT input. Replace the input board.

• Faulty STE 

output.  Check that the STE output cycles off and on by 
placing the car on inspection, change the time on the Set 
Date and Time menu to 23:59 and then wait a minute for 
the timer to roll over.  Place the car on automatic and watch 
the STE output.  Once the flag is set from the date rollover 
and the car does a redundancy test, the output will be 
cycled.  After STE turns off and then back on, the soft-starter 
fault relay should cycle as well leaving the fault relay 
energized and the CFLT input off.  If the STE output does not 
cycle, replace the output module. 

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

Nelsen Corporation C Series Programming Manual preview
C Series
Brand: Nelsen Corporation Pages: 16
National Instruments C Series Getting Started preview
C Series
Brand: National Instruments Pages: 34
VAT 168 Series Installation, Operating, & Maintenance Instructions preview
168 Series
Brand: VAT Pages: 29
Balboa Instruments Dolphin Manual preview
Dolphin
Brand: Balboa Instruments Pages: 19
Panasonic KT2 Communication Instruction Manual preview
KT2
Brand: Panasonic Pages: 12
Panasonic CZ-64ESMC1U Operating Instructions Manual preview
CZ-64ESMC1U
Brand: Panasonic Pages: 10
Eaton A201 Instruction Leaflet preview
A201
Brand: Eaton Pages: 6
Racal Instruments 1260 Manual preview
1260
Brand: Racal Instruments Pages: 94
Racal Instruments 1260 User Manual preview
1260
Brand: Racal Instruments Pages: 97
Rain Bird Image Series Quick Start Manual preview
Image Series
Brand: Rain Bird Pages: 4
Rain Bird ESP-ME3 Quick Reference Manual preview
ESP-ME3
Brand: Rain Bird Pages: 2
Rain Bird ESP-Me User Manual preview
ESP-Me
Brand: Rain Bird Pages: 140
Raindrip WeatherSmart RSC600i Installation & Programming preview
WeatherSmart RSC600i
Brand: Raindrip Pages: 36
Waterway NEO 1200 Instruction Manual preview
NEO 1200
Brand: Waterway Pages: 8
Warner Electric RFC-100 Service & Installation Instructions preview
RFC-100
Brand: Warner Electric Pages: 4
Festo CPX-AP-A-16DI-D-M12-5P Operating Instructions Manual preview
CPX-AP-A-16DI-D-M12-5P
Brand: Festo Pages: 16
Allen-Bradley 1756-L72EROM Installation Instructions Manual preview
1756-L72EROM
Brand: Allen-Bradley Pages: 16
D+H RCM 230-11-U Original Instructions preview
RCM 230-11-U
Brand: D+H Pages: 2

Brands by name

Popular brands

Load more brands