manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                           Section 7 

– Main CPU Adjustable Variables

 

7-12 

 

Table 7-3: Car Options 

Field Variable 

Min 

Max 

Initial  Units    

NCU Lant Ctrl 

0 

3 

0 

- 

 

Next Up Direction Lantern Control. 

 

+1 = Turn off hall lantern after next up time.  
+2 = Turn off cab lantern after next up time. 

NCU Pref Ctrl 

0 

1 

0 

- 

 

Next Up Preference Control. 

When set allows 

direction preference to change before the door starts 
to close after the next up door time. 

NoHC Dor 
Reop 

0 

3 

0 

- 

 

No Hall Call Button Door Reopen.

 When set do not 

reopen the door from an at floor hall call. 

Non-Simul Dor 

0 

2 

0 

- 

 

Non-Simultaneous Doors. 

 

0 = Both front and rear doors will open at the same 
time if there is a demand at both the front and rear 
openings.  
1 = The front doors will open first before the rear 
doors open if there is a demand to open.  
2 = The rear doors will open first before the front 
doors open if there is a demand to open. 

Nudg No Calls 

0 

1 

0 

- 

 

Nudge with No Calls.

  If set the doors will close on 

nudging even if the elevator has no onward calls. 

Nudge Dis Ctl 

0 

7 

0 

- 

 

Nudging Disable Control.  

 

+1 = Do not turn on the NUD output when doors are 
in nudging close mode, basically you are disabling 
nudging output.  
+2 = When doors are in nudging close mode and SE 
input is ON, keep doors open and also keep FB/NB 
output latched.  
+4 = Sound the nudging buzzer but do not close the 
doors on nudging. 

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

ABB FSCA-01 Manual preview
FSCA-01
Brand: ABB Pages: 52
Hansen HS2 Specifications, Applications, Service Instructions & Parts preview
HS2
Brand: Hansen Pages: 4
Samsung DMS2.5 Service Manual preview
DMS2.5
Brand: Samsung Pages: 32
Farfisa TD6100 Manual preview
TD6100
Brand: Farfisa Pages: 20
Racal Instruments 1266 Manual preview
1266
Brand: Racal Instruments Pages: 64
York MILLENNIUM Manual preview
MILLENNIUM
Brand: York Pages: 20
RadioMaster MT12 Quick Start Manual preview
MT12
Brand: RadioMaster Pages: 10
Xblue Networks X16 Quick Reference Card preview
X16
Brand: Xblue Networks Pages: 2
Yoshitake BSV-10F Quick Start Manual preview
BSV-10F
Brand: Yoshitake Pages: 4
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Brand: YOKOGAWA Pages: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Brand: YOKOGAWA Pages: 3
Eaton S611 User Manual preview
S611
Brand: Eaton Pages: 96
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Brand: Acuity Controls Pages: 5
Risco ProSYS 128 Programming Manual preview
ProSYS 128
Brand: Risco Pages: 232
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Brand: Bard Pages: 2
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Brand: Ros Pages: 10
YASKAWA PG-X2 Instructions Manual preview
PG-X2
Brand: YASKAWA Pages: 12
Frico IHMC6-3 Original Instructions Manual preview
IHMC6-3
Brand: Frico Pages: 8

Brands by name

Popular brands

Load more brands