manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                     Section 6 

– Main CPU Faults & Detailed Faults

 

6-60 

 

Table 6-0: Main CPU Faults 

Faults 

Description 

Possible Cause/Suggested Fix 

FVARS Tbl 
Chksum Err 

 
Field Variables Table 
Checksum Error.  The 
verification checksum 
for the main field 
variable table has 
failed. During power 
outages or brown-
outs, enough noise 
can be generated on 
the 5V DC supply to 
cause an error in 
reading the field 
variables table on 
power up.  For this 
reason, we keep the 
data in two separate 
tables.  If only one 
table checksum error 
occurs, then valid data 
will be restored. 

• No action is required.

 

Gate Switch Fault 

 
The Gate Switch failed 
on while the door was 
open. 

 

• Gate switch not adjusted properly.

 

• GS input failed on. Replace GS input on 1102 board.

 

Gate/Lock Byp Sw Flt 

The gate or lock 
bypass switch was on 
while the car was NOT 
on car top inspection. 

• Gate or Lock bypass switch on the controller 1121 board is 

in the on position.

• Gate or Lock bypass input failed on. 

Replace GBP OR LBP input chip on 1121 board. 

Governor Switch Flt 

 
Governor Switch 
Tripped. 

 

• Verify that the governor switch is set properly.

 

GOVRi Input On Fault  GOVRi input failed on. 

 

• The GOVRi input chip failed.  Replace the chip.

 

• The governor reset switch is stuck on.

 

• The GOVRi 

input is jumped on. 

GRCan Bus Off Error 

 
GRCan Bus Off Error. 
The Can bus has been 
inactive for too long a 
period of time. 

• Faulty CAN bus wiring. Check the Can bus terminal 

connections on all boards. 

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

ABB ACS850-04 series Firmware Manual preview
ACS850-04 series
Brand: ABB Pages: 296
ABB 650 series Applications Manual preview
650 series
Brand: ABB Pages: 320
ABB ACS880 Series Supplement Manual preview
ACS880 Series
Brand: ABB Pages: 50
ABB COM600 series Operator'S Manual preview
COM600 series
Brand: ABB Pages: 56
Ubisys J1 Manual preview
J1
Brand: Ubisys Pages: 2
Handicare VR2 User Manual preview
VR2
Brand: Handicare Pages: 56
Danfoss vlt soft starter mcd 500 Operating Instruction preview
vlt soft starter mcd 500
Brand: Danfoss Pages: 95
Danfoss EKE 347 Installation Manual preview
EKE 347
Brand: Danfoss Pages: 12
Danfoss VLT 5000 Instruction Manual preview
VLT 5000
Brand: Danfoss Pages: 33
Danfoss VLT 6000 Installation Manual preview
VLT 6000
Brand: Danfoss Pages: 59
Danfoss EKC 361 User Manual preview
EKC 361
Brand: Danfoss Pages: 16
Danfoss VLT AQUA Drive FC 200 Operating Instructions Manual preview
VLT AQUA Drive FC 200
Brand: Danfoss Pages: 91
Danfoss EvoFlat WSS Installation Manual preview
EvoFlat WSS
Brand: Danfoss Pages: 2
Danfoss FC 300 Operating Instructions Manual preview
FC 300
Brand: Danfoss Pages: 100
Danfoss FC 300 Operating Instruction preview
FC 300
Brand: Danfoss Pages: 82
Danfoss Optyma Plus User Manual preview
Optyma Plus
Brand: Danfoss Pages: 18
Danfoss AMV 438 SU Installation Manual preview
AMV 438 SU
Brand: Danfoss Pages: 12
Danfoss OPTYMA Plus OP-LPQM Manual preview
OPTYMA Plus OP-LPQM
Brand: Danfoss Pages: 8

Brands by name

Popular brands

Load more brands