manualshive.com logo in svg

GAL GALaxy eHydro, Manual

The GAL GALaxy eHydro manual is a comprehensive guide that provides detailed instructions for operating and maintaining this cutting-edge product. With a user-friendly format, it is easy to understand and navigate. Download this manual for free from our website, manualshive.com, to get the most out of your GAL GALaxy eHydro experience.

Share
Download
background image

GALaxy eHydro Elevator Controller                                     Section 6 

– Main CPU Faults & Detailed Faults

 

6-74 

 

Table 6-0: Main CPU Faults 

Faults 

Description 

Possible Cause/Suggested Fix 

Rear Door Close Flt 

 
The rear door did not 
reach the Rear Door 
Close Limit within the 
door close protection 
time. 

 

• Rear Door Close Limit (DCLR) not adjusted properly.

 

• Faulty Rear Door Close Limit (DCLR). Replace DCRL input.

 

• 

Trash in door track preventing door from closing. 

Rear Door Open 
Fault 

The rear door did not 
reach the Rear Door 
Open Limit within the 
door open protection 
time. 

• Rear Door Open Limit (DOLR) not adjusted properly.• 

Faulty Rear Door Open Limit (DOLR). Replace DOLR input. 

Rear Gate Sw Fault 

 
The Rear Gate Switch 
failed on while the 
door was open. 

• Rear Gate switch not adjusted properly.

 

• RGS input failed on. Replace RGS input.

 

Rear Mid Lock Fault 

The Middle Door Lock 
failed on while the 
door was open. 

 

• Faulty door lock.

 

• Jumper placed on door lock circuit.

 

• Rear door lock not adjusted properly.

 

• Faulty wiring to RLM input.

 

Faulty RLM and RLM-1 inputs (For this to occur both RLM 
and RLM-1 inputs must fail on). 

• DOLR input failed. Rep

lace DOLR input chip. 

• Rear door operator open limit is not adjusted properly

 

Rear Top Lock Fault 

The Rear Top Door 
Lock failed on while 
the door was open. 

 

• Faulty door lock.

 

• Jumper placed on door lock circuit.

 

• Rear door lock not adjusted 

properly. 

• Faulty wiring to DLT input.

 

Faulty DLT and DLT-1 inputs (For this to occur both DLT and 
DLT-1 inputs must fail on). 

• DOLR input failed. Replace DOLR input chip.

 

• Rear door operator open limit is not adjusted properly

 

Summary of Contents for GALaxy eHydro

























































































































































































































































Reviews:

No comments

Related manuals for GALaxy eHydro

PIETRO FIORENTINI DELTAFLUX MT100 Technical Manual preview
DELTAFLUX MT100
Brand: PIETRO FIORENTINI Pages: 16
IBM 2702 Information Manual preview
2702
Brand: IBM Pages: 105
Lakeshore 332 User Manual preview
332
Brand: Lakeshore Pages: 186
Eldat Easywave ST01 Series Quick Start Manual preview
Easywave ST01 Series
Brand: Eldat Pages: 2
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Brand: ICP DAS USA Pages: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Brand: National Instruments Pages: 22
Pentair FLECK 5810 XTR2 Service Manual preview
FLECK 5810 XTR2
Brand: Pentair Pages: 36
CLIMAVENETA CVM 2 Technical Manual preview
CVM 2
Brand: CLIMAVENETA Pages: 23
Kathrein ESO 125 Installation And Operation Manual preview
ESO 125
Brand: Kathrein Pages: 32
Rain Bird TBOS-BT Manual preview
TBOS-BT
Brand: Rain Bird Pages: 38
E+L RK 4004 Manual preview
RK 4004
Brand: E+L Pages: 62
Omicron BETA 9.2 Quick Start Manual preview
BETA 9.2
Brand: Omicron Pages: 17
Simplex RTL-TH DIGITAL Installation And Operating Instructions Manual preview
RTL-TH DIGITAL
Brand: Simplex Pages: 12
Arroyo Instruments TECSource 5400 Series User Manual preview
TECSource 5400 Series
Brand: Arroyo Instruments Pages: 60
Kaelus ACU0001F1V1 User Manual preview
ACU0001F1V1
Brand: Kaelus Pages: 52
WAGO 750-872 Quick Start Manual preview
750-872
Brand: WAGO Pages: 44
Infineon GTM TIM Capture 1 Manual preview
GTM TIM Capture 1
Brand: Infineon Pages: 13
Estyma iGNEO COMPACT User Manual preview
iGNEO COMPACT
Brand: Estyma Pages: 56

Brands by name

Popular brands

Load more brands