manualshive.com logo in svg

Fuji Xerox DocuPrint C5155d, User Manual

Share
Download
Fuji Xerox DocuPrint C5155d User Manual Download Page 285

7.1 Replacing Consumables

285

Replacing Drum Cartridges

The following messages appear on the printer's control panel when a drum cartridge is near or 
reaches the end of its life. 

Replacement Procedure

Important

• Make sure that the power is on when replacing a drum cartridge.

This section explains how to replace the drum cartridge R1 (K), as an example.You can apply the 
same procedures to R2 (C), R3 (M), or R4 (Y).

1.

Make sure that the machine is not operating, 
and open the front cover.

Message

Action

Ready to print

Order Drum: X

*1

The displayed drum cartridge does not need to be replaced right away, 
but have a new drum cartridge ready. 

The drum cartridge will be able to print approximately 7,500

*2

 more 

pages. 

Ready to print

Replace Drum: X

*1

The displayed drum cartridge needs to be replaced soon. 

The drum cartridge will be able to print approximately 2,300

*2

 more 

pages. Have a new cartridge ready. 

Replace Drum 

Cartridge X

*1

A drum cartridge is at the end of its life. 
The printer will stop and become unable to print. Replace the drum 
cartridge indicated in the message using the procedure under 
"Replacement Procedure" (P. 285).

Ready Replace

Drum Cartridge X

*1

Appears when a drum cartridge reaches the end of its life after you 

choose [Continue to Print]

*3

 in [Drum Life End]. Printing can continue for 

a while, but quality is not guaranteed and replacement with a new drum 
cartridge is recommended.

*1

:  The actual display shows R1 (K), R2 (C), R3 (M), or R4 (Y) in place of X. R1 through R4 indicate drum 

cartridge names. Towards the printer, from left to right, black (K), cyan (C), magenta (M) and yellow (Y) 
drum cartridges are located in sequence.

*2

:  The page yield of each consumable varies depending on print requests, documents printed, how often 

the power is switched on/off, and temperature or humidity of the environment where the printer is 
installed. For more information, see "A.3 Life of Consumables and Regular Replacement Parts" (P. 390).

*3

:

In this case, the [Ready to print Replace Drum: X] message will remain on the display. For information 
about how to configure this setting, refer to "[Drum Life End]" (P. 166).

Summary of Contents for DocuPrint C5155d


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands