manualshive.com logo in svg

Fuji Xerox DocuPrint C5155d, User Manual

Share
Download
Fuji Xerox DocuPrint C5155d User Manual Download Page 279

6.9 Non-Genuine Mode

279

6.9

Non-Genuine Mode

If you have no choice but to continue printing without changing the toner cartridge, select "Non-
Genuine Mode" to enable continued printing.

When you want to use the printer in Non-Genuine mode, use the following procedure to 
configure the mode and install the supported toner. Empty toners cannot be used even in this 
mode.

Important

• Non-Genuine mode is not covered by our quality guarantee, and the printer functions and its performance 

may not be optimal. Continued use of the printer in this mode creates the risk of printer malfunction.

• " [Drum Life End]" (P. 166) settings are ignored while in the Non-Genuine mode. Also, remaining toner cartridge 

and drum cartridge levels are not displayed. 

Note

• To disable the Non-Genuine mode, select [Off] in Step 4, below.

1.

On the control panel, press the <

> and <OK> 

buttons at the same time. 
This displays the [Consumables Menu]. 

2.

Press the <

> until [Non-Genuine] appears.

3.

Press the <

> or <OK> button to select.

This displays the current setting. 

4.

Press the <

> so [On] is displayed.

5.

Press the <

> or <OK> button to apply the 

selection. 
This displays a confirmation screen. 

6.

Press the <OK> button.
This changes the settings to the Non-Genuine 
mode settings. 

7.

Switch off the power and wait for about 10 
seconds after the display is blank to switch the 
power back on again. 
After the printer starts up, it switches to Non-
Genuine mode. 

Consumables Menu

 Serial Number

Consumables Menu

 Non-Genuine

Non-Genuine

•

Off

Non-Genuine

 On

Press OK 

to confirm

Switch power OFF

and then ON

Ready to Print

Non-Genuine

Summary of Contents for DocuPrint C5155d


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands