manualshive.com logo in svg

Fuji Xerox DocuPrint C5155d, User Manual

Share
Download
Fuji Xerox DocuPrint C5155d User Manual Download Page 108

108

4 Paper

Unsupported Paper

Using paper and transparencies not recommended by Fuji Xerox may cause a paper jam or 
machine malfunction. Use paper and transparencies recommended by Fuji Xerox. 

• Damp or wet paper

• Paper pre-printed with other printer or copying machine

• Wrinkled, creased, or ripped paper

• Envelopes that are not flat, or that have clasps

• Color paper with surface treatments

• Paper with rough surface, such as pulp paper or fibrous paper

• Symphony (Pastel Pink etc.) A4 80 gsm

Colotech Super 

Gloss

A3

160

Gloss

-

• Print  one  sheet  at  a  time,  using 

Tray 5.

Colotech Super 

Gloss

A4

210

Heavyweight

Gloss

-

• Print  one  sheet  at  a  time,  using 

Tray 5.

Colotech Super 

Gloss

A3

210

Heavyweight

Gloss

-

• Print  one  sheet  at  a  time,  using 

Tray 5.

Colotech Super 

Gloss

A3

250

Heavyweight

Gloss

-

• Print  one  sheet  at  a  time,  using 

Tray 5.

Colotech Plus

A4

200

Extra 

Heavyweight

A

• Print  one  sheet  at  a  time,  using 

Tray 5.

• When using Tray 5, load the paper 

with the center slightly curling 
upward.

Colotech Plus

A3

200

Extra 

Heavyweight

A

• Print  one  sheet  at  a  time,  using 

Tray 5.

• When using Tray 5, load the paper 

with the center slightly curling 
upward.

Colotech Plus

A4

220

Extra 

Heavyweight

A

• Print  one  sheet  at  a  time,  using 

Tray 5.

• When using Tray 5, load the paper 

with the center slightly curling 
upward.

Colotech Plus

A3

220

Extra 

Heavyweight

A

• Print  one  sheet  at  a  time,  using 

Tray 5.

• When using Tray 5, load the paper 

with the center slightly curling 
upward.

Colotech Plus

A4

250

Extra 

Heavyweight

A

• Automatic duplexing is not 

available.

Colotech Plus

A3

250

Extra 

Heavyweight

A

• Automatic duplexing is not 

available.

Colotech Plus

A4

280

Extra HW Plus

-

Colotech Plus

A3

280

Extra HW Plus

-

Paper Name

Size

Basis Weight 

(gsm)

Paper Type

Image 

Quality

Notes / Countermeasure

Summary of Contents for DocuPrint C5155d


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands